Jump to content
SAU Community

Recommended Posts

  • Replies 97
  • Created
  • Last Reply

Top Posters In This Topic

craz0

so now with the pfc in everything is fine and all u had to do was plug in with no extra wiring or mods to to the unit or wiring to make it work with the auto?

the only issue u have is the power light flashing?

steve-sst

how much is a wolf plugin worth for a r33 auto gts-t?

and who can tune it in sydney?

and as craz0 said when you installed the wolf into the auto r33 did u notice the power button flashing/going through the diagnostics?

Originally posted by walkoau

craz0

so now with the pfc in everything is fine and all u had to do was plug in with no extra wiring or mods to the unit or wiring to make it work with the auto?

the only issue u have is the power light flashing?

The PFC worked and you can drive the Car, but the Auto speed button would flash 16 times (all fast) and when you run the Auto through diagnostic mode the third flash would be long (Throttle sensor shorted or disconnected) so the Auto needs the TPS signal to work properly, when I took it for a drive it would hold out through the gears (e.g. would change from first to second at about 3500rpm with your foot just on the accelerator where it would normally change under 2000rpm) after braking/cornering and then accelerating it seem to be in the right gear (like it wasn't fishing for a gear), It kicked back gears fine as well. When it did change from first to second it was harsh (like when you put your foot down from first to second and it gives you that kick but just not as fast and no wheel spin :P)

I can't seem to find a pin layout for the actual Auto ECU either.

Does anyone know what info Pins 5, 14 and 15 push from the main ECU? all three of these go straight to the Auto ECU.

I'm figuring they push the TPS and maybe Tacho signals so the Auto ECU can figure out when to change.

I've attached a pic of the three wires going into the Auto ECU.

Just seeing if anyone knows for sure.

  • 1 month later...

Ok i got the wolf plug-in and I pluged it in and the car didn't want to start and when it did it coughed and farted and blow dark black smoke and the lights on the ECU looked like Christmas lights going of,so I turned it of :confused: don't know what happened here.

The user manual I got with the ECU is for the normal Ver 4 but not the Plug-in version, I've contacted Wolf about this and I'm waiting on a reply.

Steve-SST do you know if there is different versions of the plug-ins at all? mine has (rev 5) on it, also the PC software I got for it is Ver 4.49 what version are you currently using?

So the MAP sensor has to be conected for it to work properly? so where is the best place to hook in the map sensor line? the fuel presure reg line?

Can you still leave the AFM hooked up or do you have to remove that as well?

My car is a 93 R33 RB25DET Auto everything is stock other then a Jamex filter in the original box and I run it on Optimax.

Steve Taylor sent me the first draft of the Installation Manual for the R32/R33 GTST Plug-In ECU, I haven't had the chance to read over it yet and the manual isn't quite finished.

Thanks heaps for your help.

My Email

Originally posted by GTS-t VSPEC

You can still leave the AFM in if you want, but just make sure in the software to choose MAP sensor. Try and get a clean plenum line if possible for the MAP.

What do you mean by "Try and get a clean plenum line if possible for the MAP"?

Where did you get your line plumed into?

Thanks GTS-t VSPEC

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...