Jump to content
SAU Community

Recommended Posts

I found this on another forum, not sure if its on here but i thought i would post it anyways.

Here's a guide on how to carbon overlay parts of your car.

You will need the following parts -

tools.jpg

Carbon cloth (twil looks best)

resin

acetone (if u want to clean your brushes - i use cheap ones and bin them)

plenty of latex gloves

mixing pots

measuring jug

syringe (for measuring hardner)

masking tape

Sharp scissors

Some stirrers - I use wooded spatulars

emery cloth

wet n dry 400grit to 1200 grit

polish

1) measure up your carbon cloth for the piece to be covered. Then using the masking tape tape up both sides where you intend to cut the cloth to prevent pulling the weave then cut through the middle of the tape -

Carbonoverlay1.jpg

2) Prep your piece to be overlayed - it should be black, if its not spray it up first so a colour doesnt show through the weave. It also needs a rub down with emery cloth.

Carbonoverlay5-1.jpg

3) brush a thin layer of resin mixed with 1% harder over the part to be overlayed then press the carbon cloth gently into place and tape up to the rear of the part to pull it into shape. You may need to change your gloves often so you dont pull the weave. Leave to dry for approx 45mins

sill1.jpg

4) Start building up thing layers of resin, you will need approx 5 layers to prevent breaking through to the cloth when sanding down. Each additional layer should be added after around 7 mins when the previous layer turns to a jelly consistency. You will now need to leave it for 1 week to fully cure -

finish1.jpg

5) you will now need to trim the excess cloth off - best tool I found was a dremmel -

BEFORE:

trim2.jpg

AFTER TRIMMING:

trim3.jpg

6) Start sanding down. work your way from 400 grit up to 1200 grit wet and dry then finish with a good quality polish for a really nice shine -

finish2-1.jpg

finish4-1.jpg

Link to comment
https://www.sau.com.au/forums/topic/233499-how-to-carbon-overlay/
Share on other sites

Well not sure where in AUS u can buy the rolls but u can get about 90 sq. ft. for about $250, from the US, which would be more then ample to do a full interior (gear surround, dash ...ect...) i would think.

http://motors.shop.ebay.com/items/_W0QQ_fr...mp;_trksid=m270

Thats from the US but i im sure u can get it from other places within AUS at about the same price.

tip: when your letting it cure in your garage or whatever, put some lighting onto it, like a bedside table lamp or something that gives off a bit of heat (like you do when making homebrew or something). if its small you can leave it your oven (!) overnight if you can be bothered to sit and watch to make sure you dont burn your house down.

i definatly know that you CAN get rolls in aus, but i dont know where from.

just on the carbon rolls, My brother is a boat building / repairer by trade, and almost all the work the do is fibreglass,

anyway he said can order massive massive rolls of this overlay shit, he is considering usuing some to do up a few body piece on his car, (( he is making his own fibreglass guards bonnetc, boots etc

anyway, offtopic, for info on rolls, perhaps enquire a boat place local to you?

thats soo kool too bad its soo expensive to do and if u stuff up i guess ur fkd?

Carbon fibre prices are currently very high because there is so much demand from Airbus.

For some types of carbon fibre there is currently a long waiting list just to get raw materials.

- Adam

Edited by TheTunersGroup

in addition might be of help to sand down the original part evenly, just enough to make up for the thickness you're gonna be adding with the layer of cloth and all that resin. Especially areas that butt up against other parts and might be a tight squeeze. remember with CF you can always add more resin to make it look bigger, but you can't remove when its set.

This might be a silly question but i take it this is just an overlay yeah so your stock parts are just covered in real looking carbon fibre. This is not how you mould a whole dash is it. If not how would you make a mould for the dash. Got a mate interested in giving this a crack as well he has been thinkin bout giving it a shot for ages. Only reason i ask is the pic you posted it kinda looks like you have peeled the carbon off the stock part as in a mould. If that makes sence

This might be a silly question but i take it this is just an overlay yeah so your stock parts are just covered in real looking carbon fibre.

Yes

This is not how you mould a whole dash is it.

No

If not how would you make a mould for the dash. Got a mate interested in giving this a crack as well he has been thinkin bout giving it a shot for ages. Only reason i ask is the pic you posted it kinda looks like you have peeled the carbon off the stock part as in a mould. If that makes sence

To do what you're thinking is a lot more involved than just laying a sheet of carbon cloth on it and resining it up. You need to start by protecting the dash (foil, gladwrap, tape depending on the chemicals you're gonna use). then spray it with a coat of gelcoat, then lay fibreglass on top of that. once the fibreglass has started to tack, you might wanna build up some wood reinforcement so that it holds its shape when you pull it off the dash. Once you've got all that done you'll have a mould, which you can use to make your plug (replacement dash).

indeed, be very careful about putting resin hardened carbon cloth in front of your face in a car when it can flex. unless you like picking shards out of your eye. as stupid as it sounds, that's one instance where a fibreglass backed CF would be better as it won't splinter as much.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...