Jump to content
SAU Community

Recommended Posts

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

atleast 20,000 kms on 100 octane (the purple pump) from united on princess hwy near springvale,police rd making just under 300kws tuned on 100octane no probs what so ever....filled up last wenesday at $1.12 a litre

in my opinion....

i have used both united plus and v-power. whether its psychological or actual gains i believe in my opinion the v-power was a much better fuel for my car based on daily driving performance and kilometres per tank.

vehicle: r34 GTT sedan. completely stock no engine mods or exhaust.

fuel period used: 1 month on each.

route taken: same route 7days a week to work and back.

result:

the exact same route was taken each day. i did my best to drive it consistently for the 2 month test period. no flooring or burning people off at the lights mostly freeway driving with the occasional squirt.

the result i got was 455km out of a tank filled consistently each time at 51 litres using united plus fuel.

whereas

the v-power gave me 475km out of a tank filled consistently each time at 51 litres.

Not much difference in terms of km outcome however i did notice when using united plus petrol it did run a little more rough. cold starts were not as smooth as when i ran with v-power. when i did give it a little squirt it wasnt as smooth as v-power. v-power just seemed more suited to my car. the engine seemed more responsive and quieter and not as hesitent. Overall a much better fuel in my opinion.

In conclusion i would have to say, if you can afford to drive a turbo car or any type of sports car, the last thing you should be complaining about is fuel. Dont be a tightass over a couple of dollars because at the end of the day if all fuels were priced the same i gurantee everyone would be using "reputable" brand fuels.

cheers everyone

Edited by humsup34
Was there any difference in power between the tunes? Have you filled up with 98 since when 100 wasn't available?

there was considrable difference between 98 and 100 fuels when i had mine tuned, at racepace, more power thru the whole rev range.

i have used 98 a couple of times when 100 was not available but i stayed away from boost and did not load the engine.

Ive recently been using the united 100 as my car has been tuned for 100. Its great, knock levels are actually better on the same tune. Dont care about ecconomy at all, just knock and power.

I'm now testnig a E85 blend and slowly adding in more timing to the tune..e85 is the shit, havnt done a dyno but knock is staying ok with a few more degreess accross the map everywhere. ethanol is great! just dont spill it on ur paint..

went to fill up on 100 today on princes hwy, they were out..

they always seem to be out of 100 octane on princess hwy but i guess taht just means that there stock just rotates and they dont have old fuel

  • 1 year later...
  • 4 weeks later...

DuFFR32, that is not entirely correct. The higher the octane[ RON] the less chance of knocking and pinging. RON is the fuels ability to resist knocking not volitility . Higher RON lets the ecu feed in more timing for more power until the knock sensor hears the knock or approach and reduces the timing back to safe levels.

well thats just your opinion..

it could not be souly responsible for it, there are other factors that may have obviously contributed. All i am saying is i dont believe its wise to be running this fuel consistently in a NA. Why not just run it on normal unleaded and you will have no drama's

Well it's my opinion too. Most modern cars are quite capable of running ethanol, whereas older cars can be totally stuffed up. I don't know where the cut-off is, it probably varies by model, but I wouldn't even think of putting ethanol in, say, a pre-1990 car. Generally I'd say if your car was built before ethanol became widely used, don't do it.

I would never put ethanol in my car anyway unless it's specifically designed for it, but I'm prejudiced ;-)

I've said it before and I'll say it again in yet another thread about United Fuel.

My GF's Datsun 1200 has run exclusively on Plus ULP (95) octane for at least the last two years. All the fuel system, carburettor etc are fine, and this is in a motor dating from 1973!

I run the Boost 98 in my car when I have to, the only difference is that it seems to use more of it than normal 98 octane.

My old VN wouldn't start properly on United fuel (yes I did test this by running the tank down and filling up from a normal servo and United). I can't explain this phenomena.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
×
×
  • Create New...