Jump to content
SAU Community

Recommended Posts

so, why have they been labelled as that, when in fact, they are the complete opposite. a turbo is actually a blower and superchargers are more litterally compressors (bar centrifugal, but they're gay anyway)

so does anyone know why they have been incorrectly named so?

and please dont turn this into a turbo vs. supercahrger thread, i dont care about your opinions of centrifugal chargers either lol :thumbsup:

cheers,

Ben

Link to comment
https://www.sau.com.au/forums/topic/238990-why-is-a-turbo-a-compressor/
Share on other sites

Probably because back in the day, they used to use cabin "blowers" off aircraft as superchargers, where a mechanicly drive air pump was used to feed fresh air into the cabin / cockpits, were adapted to engines to make them faster.

and IMO a turbo compresses air and a supercharger (exept centrifugal superchargers cause I hate them :thumbsup:) just simply forces more air into the intake which the engine cant swollow hence positive pressure in the intake.

all the terms youve described are just slang really, they are by no means standardised.

when it comes down to basics, exhaust or belt driven charger are still superchargers. they both increase (super) the mass of air (charge air) going into the engine. turbo is just a term to refer to the turbine in their design

a turbo is a turbine-it consists of a compressor "fan/blades" and a turbine "fan/blade" on a shared shaft. It is an air compressor whereby its sole aim is to force more air into the intake than was previously there, so in essence it is a compressor, but i see where you're coming from. I think the main reason why they named them a turbocharger is to distinguish them from superchargers.

R32 abuser, i dont see turbos as compressors, they move a shitload of air, air hits restriction (your motor not being able to swallow it) and this is what generates pressure, whereas superchargers actually compress the air before feeding it into the motor.

R32 abuser, i dont see turbos as compressors, they move a shitload of air, air hits restriction (your motor not being able to swallow it) and this is what generates pressure, whereas superchargers actually compress the air before feeding it into the motor.

what? :blink:

air may be forced into the manifold by centrifugal force or by a positive displacement type device. pressure is simply a result of mass volume and temperature.

whatever youre using to compress the air, its still compressed air.

on a side note, moving "shitloads" of air doesnt necessarily make pressure. a fan can move a lot of air but cant create pressure. at least 0.001 psi doesnt count.

note many of those ebay electric "superchargers", which are high speed fans that push a large CFM, but once the pressure builds past atmospheric pressure theyd be lucky to push 1 psi in some cases.

AFAIK

Turbochargers are internal compressors (The air is compressed leaving the turbine). The fan blades are designed to compress air coming in, as opposed to just being a pump.

There are different types of superchargers, some are internal compressors (and essentially work the same as a turbocharger) and some are external compressors, i.e. they're just a pump and the compression occurs in the manifold.

The term "blower" would then refer to any supercharger that acts as a pump and not a compressor.

My friend wikipedia has more:

http://en.wikipedia.org/wiki/Turbocharger - Note "compressor"

http://en.wikipedia.org/wiki/Roots_type_supercharger - Note "pump"

zoomzoom, if you read over what i said again, i said the turbo moves the air, and when it hits the restriction, the pressure builds. i dont think turbos actually compress the air, they 'blow' alot of it, it has no place to go, so the pressure builds up. superchargers 'compress' the air before feeding it into the manifold. are you with me? yes its still pressurized air, at the end of the day its the same shit, but they both get there in different ways, and have been named accordingly, but the names they are given seem to be the exact opposite of what they are. thats how it works in my head anyway

hackerX. read the turbocharger one again, it also calls the turbo a pump

A Turbocharger, often called a turbo, is a small radial fan pump

i think the wording on that site isnt the best

what i didnt know was that the turbine actually compresses the air as it enters, never heard this theory before, even wiki says its a pump :thumbsup: lol

It implies being a pump as well :banana:

IMO, a turbo's compressor wheel compresses the air in the same way that a pipe with one end larger than the other would compress air. Where as your typical supercharger just takes air and pushes it through at a greater rate than natural flow. Any compression happens post-supercharger.

I'm happy to be wrong on this though.

Turbo's sole job is to suck hard and release at will. (like girls lol jk girls.. but sort of still the same).

Because turbos are constantly compressing and releasing its power almost simultaniously, the compression (caused by the impeller) is the main man.

Flow is proportional to impeller speed.

Differential pressure across an impeller is proportional to the square of the impeller speed.

Power absorbed by the impeller varies with the cube of the impeller speed.

Yes Turbos Suck and Blow but all relies on the dynamics of the impeller which creates small degree of compression. Turbos are also often called a centrifugal compressor, a dynamic compressor or even an aerodynamic compressor.

So u cant really call Turbos just "blowers" or "suckers" because they do both. The master here is the dynamics of the impeller (The director of Compresson if u will).

Now Superchargers.. who bloody cares. lol na correct me if im wrong but they rely on compression but concentrate more on the pushing (blowing) for its power.

That sound about right?

Edited by 1R34SON

both turbos and superchargers are compressors. and they both cause pressure in the same way. they both force air in and when it has nowhere to go the pressure increases. the only difference is how they are driven, which does mean that they have different properties. a turbo is driven by the exhaust, so the the throttle has to be open to create boost, as the engine needs to be pushing air out in order for the turbo to be forcing air in.

a supercharger on the other hand is driven by a pulley from the motor so they will create boost regaurdless of throttle opening. this is because they are forcing the air in even if the throttle is shut. however some superchargers won't create boost at idle. and i'm sure that with the right compressor and exhaust housing sizes you could make a turbo create boost at idle (without the use of an anti-lag system).

at 100% throttle the only thing causing restriction (which creates positive pressure) is the ratio of how much air the engine takes in compared to how much air is being forced by the compressor (either a turbo or a supercharger). the higher the ratio of air forced in to the air used determines the boost pressure.

also about the whole turbo sucking thing. a supercharger will suck the air once the throttle is opened. but at idle it isn't sucking in any more air because very little air is being used. at the same token that a turbo isn't really sucking any air at idle either. so once the throttle is opened, both a turbo and a supercharger will both suck and blow. a supercharger can't blow air into a motor without sucking the air in first. that would be like trying to blow up a balloon without taking a breath in first.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wow, thanks for your help guys 🙏. I really appreciate it. Thanks @Rezz, if i fail finding any new or used, full or partial set of original Stage carpets i will come back to you for sure 😉 Explenation is right there, i just missed it 🤦‍♂️. Thanks for pointing out. @soviet_merlin in the meantime, I received a reply from nengun, and i quote: "Thanks for your message and interest in Nengun. KG4900 is for the full set of floor mats, while KG4911 is only the Driver's Floor Mat. FR, RH means Front Right Hand Side. All the Full Set options are now discontinued. However, the Driver's Floor Mat options are still available according to the latest information available to us. We do not know what the differences would be, but if you only want the one mat, we can certainly see what we can find out for you". Interesting. It seems they still have some "new old stock" that Duncan mentioned 🤔. I wonder if they can provide any photos......And i also just realized that amayama have G4900 sets. I'm tempted too. 
    • Any update on this one? did you manage to get it fixed?    i'm having the same issue with my r34 and i believe its to do with the smart entry (keyless) control module but cant be sure without forking out to get a replacement  
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if something was binding the shaft from rotating properly. I got absolutely no voltage reading out of the sensor no matter how fast I turned the shaft. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if shttps://imgur.com/6TQCG3xomething was binding the shaft from rotating properly. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
×
×
  • Create New...