Jump to content
SAU Community

Recommended Posts

I recently acquired a consult -> USB cable and discovered Code 21: Ignition Signal Circuit. Im from the USA and i put this rb25det neo into an s14. Im running the car on a Stagea R34 Automatic ECU. I did a search on the forum and did read some other threads with a similar problem, but none helped. The motor has been running for a few weeks, but I cant get cylinder 1 to fire. I rotated the coils and plugs around so thats not the problem. Power voltage to coil 1 is your normal 12-13.5V, but the trigger voltage was only .3V (all other coils were ~.8V). I know my problem is either in the ECU or Wiring Harness, but i also read a thread on here where someone had a bad ground? Should i test the continuity to coil 1?

What do you guys suggest. Ive pretty much tried everything I can think of. I dont have access to try someone elses ECU or Wiring harness, as there are only a handful of these motors in my entire country. How often do these ECUs go out? I tried to test the voltage coming out of the Ignition Signals to each coil (directly on the ecu), but I couldnt get a reading for the life of me. Besides this one problem, the motor starts, idles, and drives as good as it gets (with 5 cylinders that is).

Please help me out here gents!

Link to comment
https://www.sau.com.au/forums/topic/239162-rb25det-neo-code-21-cylinder-1-dead/
Share on other sites

I don't think you can check the ecu trigger signal using a multimeter gotta use oscilloscope. I've done this on my car coz it was misfiring.

post-2214-1223473736_thumb.jpg

The signal should have a sawtooth sorta pattern (i think it's current control). If you don't get a signal it's proabbly either the wiring for the trigger signal is stuffed or the ecu itself is stuffed. You can check the wiring by just checking teh resistance from teh corresponding ecu pin to the coilpack connector for your dead cylinder.

How do you know the cylinders not firing anyway do you get blacksmoke out the exhaust?

I don't think you can check the ecu trigger signal using a multimeter gotta use oscilloscope. I've done this on my car coz it was misfiring.

post-2214-1223473736_thumb.jpg

The signal should have a sawtooth sorta pattern (i think it's current control). If you don't get a signal it's proabbly either the wiring for the trigger signal is stuffed or the ecu itself is stuffed. You can check the wiring by just checking teh resistance from teh corresponding ecu pin to the coilpack connector for your dead cylinder.

How do you know the cylinders not firing anyway do you get blacksmoke out the exhaust?

I know because ive disconnected the coils during idle and the motor doesnt change at all. I rotated the coils and plugs, so I know its either wiring or the ECU. How would I check the resistance on the wiring to coil one? Just complete the loop by running a wire directly from the coil to the pin on the ecu?

Thanks for the help my friend, I do appreciate it.

I know because ive disconnected the coils during idle and the motor doesnt change at all. I rotated the coils and plugs, so I know its either wiring or the ECU. How would I check the resistance on the wiring to coil one? Just complete the loop by running a wire directly from the coil to the pin on the ecu?

Thanks for the help my friend, I do appreciate it.

Do you have a pinout diagram? This may be the one although there are variations:

http://www.skylinesaustralia.com/forums/in...st&id=31087

Do you have a pinout diagram? This may be the one although there are variations:

http://www.skylinesaustralia.com/forums/in...st&id=31087

Yes i have the pinouts, thanks though. Im very surprised nobody has ever had this problem before?

Open the ECU and check out the two large power transistors bottom left (plug facing you) up against the side, heatsinked to the body of the ECU.

I'm guessing the one of them will show signs of burning out, will be brown/charred and very brittle....to the point when you remove the heatsink to get a clear look it will break.

That's my guess, I've seen it before on R34 ECUs, hopefully I'm wrong.

4x now i have seen error 21 keep a car off the road for months with the owner scared to drive it, 4x now i have switched to new coils and its been fine.

that being said, if your cylinder is dead completely, it may also be the wiring to that coil

4x now i have seen error 21 keep a car off the road for months with the owner scared to drive it, 4x now i have switched to new coils and its been fine.

that being said, if your cylinder is dead completely, it may also be the wiring to that coil

I dont think it is the coils, as when I rotate them, the same cylinder wont fire. Im guessing at this point it must be wiring.

so disconnect the ecu, isconnect the bad coil clip, and use the pinout diagram and a multimeter on the contnuity setting to get a simple answer of wether or not the cables get to the other end or not. with ecu and battery off, you can poke wherever you want and cant hurt anything.

check that one pin goes to ground, one goes to the battery, and the other will be the trigger for example if there are 3.

use a bit of speaker wire or something to go up from the ecu to one of the pins, and then find the other end on the ecu.

Well i have continuity between the ecu and the coil on all 6 coilpacks, so I'm definitely thinking it is the ECU at this point correct?

And BTW, it's cylinder 6 that wont fire, not cylinder one. I was backwards on my counting order.

  • 9 years later...
  • 1 year later...
8 hours ago, bistratoaie said:

I seem to have the same problem and cylinder 6! Anyone got any solution?

I just read everything in this post, seems to me all the answers are there. It boils down to continuity or fried ECU.

  • 5 months later...

Turns out piston #6 had shat itself and got a little hole in it as fuel was just dumping into the sump, have done a rebuild with new forged pistons, rings, bearings etc and she's running beautifully. Ignition circuit also goes hand in hand with knock sensors I believe, I had an ignition fault code 21, and tried everything to sort it after buying new splitfires, spark plugs, coilpack harness, AFM all that jazz, turns out one of my knock sensors was crushed and that was my ignition problem solvered ☺️

  • Like 1
On 6/30/2019 at 11:45 PM, bistratoaie said:

Turns out piston #6 had shat itself and got a little hole in it as fuel was just dumping into the sump, have done a rebuild with new forged pistons, rings, bearings etc and she's running beautifully. Ignition circuit also goes hand in hand with knock sensors I believe, I had an ignition fault code 21, and tried everything to sort it after buying new splitfires, spark plugs, coilpack harness, AFM all that jazz, turns out one of my knock sensors was crushed and that was my ignition problem solvered ☺️

It occurs to me that a compression test might have been a good idea. Is that how you found the fault?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...