Jump to content
SAU Community

Recommended Posts

Hi everyone,

Recently on a long track, the Apexi AVC-R (EBC) fitted in my R34 GTT, clocked 302km/h as the top speed during the length of the Journey, i have an after market Nismo Meter which shows speeds upto 300Km/h but unfortunately i was lookin on the track and not the speedometer. Although I do remember shifting to the fifth gear cause the revs were upto 6.7 on the 4th gear (never had to floor car above 4th gear) and after shifting into 5th i was still pushing on the pedal.

As for other mods, the car has a Front Mount Intercooler, the Apexi EBC as listed above, full 3.5inch cat back exhaust and was running it on 0.76 Kg/cm2 Boost.

Do you guys think the AVC-R has recorded some false value? or is 302km/h a comfortable speed for the RB25DETT engine? the car is 1998 so the engine is not brand new?

Any expert opinion or comments guys? im confused?

Link to comment
https://www.sau.com.au/forums/topic/240286-r34-gtt-top-speed/
Share on other sites

whats your diff ratio, and tire size? work out your theoretical geared top speed

then you will need to find out your drag coefficient which isnt usually very accessible data unless you either

1. have a wind tunnel

2. find your actual top speed and have accurate power figures as well

ps. 302kmh is approx 187mph thats pretty fast for a standard skyline

two main components for calculating theoretical top speed

rolling resistance

drag due to air resistance

rolling resistance is fairly linear so easy to calculate

drag due to air resistance has a cube relationship to speed.

so the increase of 250kmh to 300kmh is a factor of 1.2

the power increase you need is the cube of this factor (1.2) = 1.728

using very average numbers for coefficient of friction, average combustion efficiency and average drivetrain losses, you need 408hp (flywheel hp) to reach 187mph. very rough numbers though but just to give you the scale of things.

Edited by clip14

Hmm interesting thread... *subscribing*

I hit 265km/hr on a pretty worked RB25 before... that was the reading off my F-CON Navigator (I only have a 180km/hr dash), and am not sure if its entirely accurate.

...not with a 3.6 diff

BTW Thelma & Louise didn't even reach that speed in the last few seconds in the T-Bird!

In reply to the post above,

the T-Bird after leaving the cliff will accelerate to the point of terminal velocity where the wind resistance balances out the gravitational pull.

The T-Bird's terminal velocity would be a maximum of 60m/sec = 135mph = 216Km/Hr >_<

  • 6 months later...
speed limter? no mention of an aftermarket ecu?? and nothing about removing speed limiter.. so i assume max speed at 180... if not i don't think you'd get that speed on 0.76 Boost...

The speed limiter isn't in place and its an after market Nismo Speedometer so reads upto 320km/h and yes its calibrated!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...