Jump to content
SAU Community

Recommended Posts

Have just had my car tunned 98 GTR

list of mod

steel wheel turbos

HKS evc boost controller

Hard intake and cooler piping

cooling pro fmic 80mm

tomei fuel reg

std injectors

std afm

std fuel pump

manifolds

std dumps

3" fronts

3" exhaust straight threw atm

lightened flywheel 12lbs

pfc

cam gears

after tune got 260awkw with injectors at 96% duty and didnt want to push them any harder had fuel pressure bumped up to 70psi running 1.25bar have included dyno sheet.

is this a good tune? have read others dyno resaults and some getting 300awkw on std injectors why are mine maxed out?

post-51272-1225035455_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/241868-gtr-dyno-tune-260kw125bar/
Share on other sites

Have just had my car tunned 98 GTR

list of mod

steel wheel turbos

HKS evc boost controller

Hard intake and cooler piping

cooling pro fmic 80mm

tomei fuel reg

std injectors

std afm

std fuel pump

manifolds

std dumps

3" fronts

3" exhaust straight threw atm

lightened flywheel 12lbs

pfc

cam gears

after tune got 260awkw with injectors at 96% duty and didnt want to push them any harder had fuel pressure bumped up to 70psi running 1.25bar have included dyno sheet.

is this a good tune? have read others dyno resaults and some getting 300awkw on std injectors why are mine maxed out?

Try running less boost and more timing. And are you sure the tuner wasn't just winding in the fuel to compensate for a dying pump? Maybe a new pump might help to keep things in order. But without seeing the car, it's anyones guess really.

is this a good tune? have read others dyno resaults and some getting 300awkw on std injectors why are mine maxed out?

I did not read this before.. but I agree your fuel pump needs upgrading.

I would also replace injectors with new 550-700cc depends what you want to achive and headroom.

Replacing old parts for new is a good thing and a safe thing to do.

std fuel pump

after tune got 260awkw with injectors at 96% duty and didnt want to push them any harder had fuel pressure bumped up to 70psi running 1.25bar have included dyno sheet.

is this a good tune? have read others dyno resaults and some getting 300awkw on std injectors why are mine maxed out?

Hey,

It should be easy to figure out whether the pump's not up to the task - get a graph of

fuel pressure on one of those runs (or have someone watch a gauge if it's in the engine bay),

if it falls off at maximum flow your pump needs help.

Regards,

Saliya

I also think dying fuel pump.

Silly to bump the rail pressure without checking the pump is ok first.

Very dangerous infact as in a few weeks the pump could be in even worse state then you'll really have more drama's

Seems a little low..

Stock turbos, injectors, no gears, just exhaust/dumps & power FC made me 250kw at 12 psi.

That’s actually a little high… 250rwkw is generally a result of 1bar.

fuel pump seemed fine i watched the gauge and held pressure strong but at 85psi its was bouncey on the gauge so that why we wound it back to 70 and when on a dyno run it woundnt drop back down or the neddle wounldnt go bouncey at all. but i have just bought a 044 im setting up a swell pot in the boot because i do hill climbs but really dont wanna drive 400km to get another tune on it already have already drop $1000 into tuning it.

when put this new fuel pump in will it stuff up all the a/f ratios?

Very much a potential yes.

If your running a higher than stock fuel pressure to counteract a dying pump

And then put the new pump in, you could find that its running even more pressure = bad.

Ha, yeah they need to learn how to scale their graphs a little better...

Did you run a flow test on it? No point having pressure if you got no flow.

Of course the a/f will be affected, if people are running 280 maxxing the injectors out, and if yours are on 96% then you technically should have almost 280kw worth of fuel going into it with a decent pump.

and theres no way you get 260AWkw running standard turbos and under a bar HAHA.

well he said "steel wheel turbos" not standard turbos. (or did you mean someone else?) certainly my 32 n1s give me about the same at 0.8 bar which is all we are allowed to run.

travis we make very similar power in our targa car at 0.8 bar using standard injectors, standard fuel pump, standard afms etc. we are also running over 90% duty cycle which is high enough for me considering how the car is used (no point pushing it to a dangerous level when fuel quality and temperature can vary so much). Not sure where these 280 or 300kw numbers are coming from standard injectors unless maybe they mean rwkw not 4wkw?

definately check the fuel pump is OK to be safe but we don't get any more than you do with new pump, clean and tested injectors and nismo adjustable fpr. easy to check since it sounds like you have a fuel pressure gauge - pressure should climb with boost right to the top of the rev range...if it drops off up high you have fuel pump or fuel pump wiring problems

yes i noticed it to that it only goes to 140kph, the tunner said something that it wasnt getting traction would this be the case and he said his rollers where warn? i will be putting a swell pot in and a 044 pump and i re-run the wiring aswell.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
    • What ECU are you running? This is probably the biggest question. If it's a PowerFC, I'd probably change the ECU and get something newer that will handle the injectors in a nicer way.
    • FYI: Racebox RE7R Custom Tunes Released!   https://goracebox.com/.../2017-infiniti-q50-q60-re7r-tcm...   FOR GEN 2 (21+) VEHICLES, PLEASE SEE NOTE AT BOTTOM See more   But whomever tuned your car is the tuner you should go back to, AMS, Sonictune or BT Tune....
×
×
  • Create New...