Jump to content
SAU Community

Recommended Posts

Hey guys have found what turbo i want for my rb20 but there are 3 differant types of the 8cm exhaust housing one, they are:

TD06S-20G 8cm

TD06S L2-20G 8cm

TD06SH-20G 8cm

Going too be buying one soon and would like to know the differances, names of the turbos were taken off the greddy website...

Greddy Wedsite

Thanks Luke

Link to comment
https://www.sau.com.au/forums/topic/242126-td06-20g-differances/
Share on other sites

TD06S-20G 8cm

TD06S L2-20G 8cm

TD06SH-20G 8cm

Basically the TD part is the turbine, the 20# is the compressor

So the TD06SL2 has a different exhaust wheel to the TD06S, from the dyno sheets i have seen there is no difference in response or power. The TD06SH is bigger again and would most certainly be laggier as it is the exhaust wheel used on the T67-25G and TD06SH-25G

Yes the nice Trust spec turbine is the "TD06 SL-2" version . More open blades and I think from memory 11 blades rather than 12 . It's actually slightly smaller in diameter than garden variety TD06 turbines but works quite well for its size .

Mobs here in Australia can build you turbos based on that turbine , GT Pumps is one . They also usually stock the three trim sizes of that compressor family - 16/18/20G . Don't quote me but TD05/6 may be based on the same center section .

The main challenge , as always , is getting the flange to suit your exhaust manifold . Trust Greddy sometimes use a 3 hole pattern but I'm sure I've seen Mitsy (MHI) turbine housings with T3 sized mounting flanges on them .

Whats the bite for a Trust TD06xx these days ?

A .

L2 is the pick of the bunch....it is the turbine that comes in the Greddy kit :laugh:

Have you seen a straight TD06 vs the TD06SL2 comparison? Interesting to read if others experiences vary.

I dont think there is really much in it. vsute has an R32 GTSt that is near identical to mine. Same ECU, same injectors, same tuner, same dyno and both completely std RB20s with cam gears. Our graphs are identical except for the fact our cars run different diam tyres so the dyno sheets look identical only just offset from one another.

He runs the L2 i run the norm TD06, i dont think its even a TD06S, well not according to the tag on the compressor cover. So i wouldnt lose any sleep over makign sure its an L2 version.

I know its only one expample, but its a pretty controlled example. Our cars made within 2kws of each other at the same boost level.

260rwkws at 18-19psi. I have run 22psi in it, but i dont think there is much more power in it. Shit load more midrange, but ultimately about the same top end power

gallery_462_50_59282.jpg

The red line was with some cams i tried, the amount of ignition we were able to wind into the engine suggested that the cams were simply too big for the little RB20 with a small TD06 8cm on it. Cams were Apexi 260/8.8mm

The std cams work pretty well, with over 240rwkws from 130km/h to 185km/h

I have no idea. The workshop i use for tuning is doing something right as he gets great results out of std cams. My car was on Dr Drifts dyno and i think it made 20rwkws more then any other std cam RB20 he had run before. Not sure if it was 20rwkws, but was soemthing like that. That was almost 2 years ago so he may have seen some more decent RB20s come through the workshop.

But i have to say if i was going to try cams it would be the Tomei 256 jobbies. Some also have good results with the HKS, but i just sold my set as i was not willing to spend the dollars experimenting when what i have already works well enough for me.

LOL, did i ramble enough? :) Real answer is fark knows :) It woudl be interesting to see you do a proper before/after comparison on the same dyno and same tuner. It seems Dr Drift got good reslts with the Tomei....but more cars getting the same result would be nice :)

Have you seen a straight TD06 vs the TD06SL2 comparison? Interesting to read if others experiences vary.

I say its the pick of the bunch because you get the L2 with the manifold pipes etc etc for the RB20.

I have seen greddy kits come with turbos not specified for the kit, however, trust seemed reluctant to do such a thing.

However, yes looking at the specs on the turbos from greddy they are a much of a muchness. :ermm:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...