Jump to content
SAU Community

Group Buy: R33 Gtst And R34 Gtt Cold Air Box Cover


Recommended Posts

  • Replies 211
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

non for r32? =(

no r32 as yet. for the next group buy ill have R32 box and GTR box and the R34 box will be altered a little to fit the AC condensor so no cutting or mods required.

hey ash.. mine required no cuttting for the condensor.. fits nice so dont think i installed correctly

anyone get pics for an install?

Edited by .:: GimpS-R34 ::.

Thanks for organising this ash

ill probably install mine on the weekend when i have time so ill hit u up with a trader rating then (if its good ;))

i have a mate that would be interested in a 32 box and can probably get another 1 or 2. Then i have a couple of mates with 34's and 33's that will probably want one also so im sure there will be no shortage in demand for these

Still pretty keen to hear from some people with 33's in regards to how there install went

so far though im impressed with how the box looks and my dummy fit looks like its gunna be doing the job :action-smiley-069:

I just put mine in then. And its a hot day, i was working on it inside and was still sweating like crazy lol

mine needs a few more adjustments to sit it down properly where its supposed to be but overall so far so good, seems to have dropped my temp down a bit ;)

Just as a note.... My afm would not fit through the hole in the air box, perhaps cause mines a Z32? anyways have something handy to trim it out a bit.

and if your going to install it, budget at least an hour for all the little fiddly bits

Not to hard to work out but

hey ash, just letting you know i havent received the replacement blank box yet ;)

if you want i can meetup with sheng and give him the one with the holes pre made in it (thats if you havent sent his out yet)

or i can meetup with anyone who wants to buy it (just transfer the funds to ash)

dori thats actually a great idea. have sent both you and sheng a pm

your box is on its way and as i said via PM im sorry for the stuff up in sending you the wrong box and you have had to wait an extra week from the others. send me your bank details ill give you a refund and you get a box for free :)

sheng if you can pick up the box from dori32 send me your bank details and ill refund you postage :)

my inbox is getting full from alot of messages please email me on [email protected] for a quicker response if you want a box as i have about 5 or so left over.

ta

Ash

hey mate i have an r34 GT

do you rekon one would fit ?

I'd be really interested and i would need it shipped out to syd willing to pay etc

Let me know cheers

as long as its an R33 or R34 and isnt a GTR it will fit.....

Inline with GB rules about having a start & end date - this is now closed.

http://www.skylinesaustralia.com/forums/Th...Gro-t81129.html

SAU is clamping down on these GB's that never occur, never end, and so on.

PM me if you have a problem. However, before you PM me think about this.

A group buy, is a group of people buying the product together to lower the price.

Buying single units here and there is not what constitutes a GROUP BUY

Thanks

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...