Jump to content
SAU Community

Recommended Posts

Hi guys, when I don't drive my car for about a week, the battery just dies. I can hear the car trying to crank but it just doesn't start. The battery is quite tiny, and I can't read the label to find out the cranking amps, but I know it is a Pitwork G Series.

It's probably because of an aftermarket stereo/subwoofer and alarm/immobiliser.

Wanted to find a battery charger that I can connect to the bonnet terminals that will charge and then maintain that charge, for when it just sits in the garage. Any recommendations? Oh and should I disconnect my subwoofer cable when I am charging??

Thanks very much.

post-49469-1226391838_thumb.jpg

post-49469-1226391860_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/244365-battery-charger-recommendations/
Share on other sites

i wouldn't bother disconnecting the amp, with that sub i can guess that your amp is pretty small so that wouldn't do a prob.... I got 1500rms amp and i get no problm starting.... how old is your battery? being in the boot its hard to see how old or how much acid is in the battery, i had your problem once and all it was was all the acid had evaporated. I thought the battery was still full because in the boot it doesnt get dirty and it looked fresh lol.

actally looking back i guess it wont hurt to disconnect your amp, just unscrew your fuse holder that you can see in one of your pics above....

LOL I had a Pitwork battery too. Original from Japan.

Anyway I swapped with a Boche Silver and never looked back.

BUT I did buy a cheap "trickle" charger which keeps it charged if I am not driving it for a few weeks.

Cool, thanks for everyone's replies.

I went to Autobarn and SCA and decided to get one of the Projecta battery chargers, either the 2.3 or 4 amp one. They automatically switch from full charge to maintenance, so I can just leave them on. They said that I should get the lower amp one as the battery will last longer???? If the charger is just at maintenance, does it matter what amp rating it is?

Cool, thanks for everyone's replies.

I went to Autobarn and SCA and decided to get one of the Projecta battery chargers, either the 2.3 or 4 amp one. They automatically switch from full charge to maintenance, so I can just leave them on. They said that I should get the lower amp one as the battery will last longer???? If the charger is just at maintenance, does it matter what amp rating it is?

it doesn't matter what amp rating it is if it is used as a maintance charger. keep in mind though if the battery is low on charge make sure you allow for ventilation in the boot if you have a non sealed lead acid battery. you'll end up getting an acid smell in the boot and the battery might breath a little to much and weep acid out the caps. ;)

have you measured the Amperage drain on your battery when switched off? that would give you an indication of which one you need

all vehicles have a current draw of at least .01amps-.05. any larger then this the battery will go flat. you will need to get that fixed first before buying a charger. the only vehicles i've seen with hugh current draws are late model euro cars like bmw and mercs, but they have a battery that can handle that sort of current draw for a period of time only.

Agreed.. Haha

In all seriousness why dont you just invest in a decent new battery?

I'd love to, but I have no idea how to exchange the battery myself (see pics). How do I actually get to it? Do I need to unscrew the whole metal plate separating the boot from the rest of the car?

I'd love to, but I have no idea how to exchange the battery myself (see pics). How do I actually get to it? Do I need to unscrew the whole metal plate separating the boot from the rest of the car?

Yeah you need to pull the whole plate out, it's held in by 12 bolts then just lifts out.

If you get a bigger battery you'll need a new ground cable and terrminal as the new battery will sit higher.

I got a D34 in the standard position and it works a treat, I also have a CTEK charger.

Here's what I use on my car:

img1001yd3.jpg

It comes with a two types of terminals... the standard clips, and ones that can be attached via bolts (2 eyelets). I attached the eyelet terminals to the engine bay jump start terminals.

The charger then plugs in like this. Just unplug and go when you want to.

img0995te6.jpg

(yes, the bonnet still closes with this attached)

I bought the charger from here:

http://www.batterydoctor.com.au/store/view...?product=BFA012

used paypal, and was delivered to my door within 3 days.

$69 delivered

It's a set and forget type thing. It will not overcharge, and it turns itself off automatically.

I use a ctek charger as well and we use one at work. they are compact and easy to install. I've mounted mine to the battery box in my boot and when the cars not in use i just plug in 240. I do agree with sinstr, get a decent battery, then buy a charger.

Ok, I bought a Projecta 4300mAmp charger, but when I try to charge the battery from either the bonnet terminals or directly on the battery terminals, the power light is on the charger but it is not charging.

The manual said that this may be the case if the battery is truly dead, and cannot be recharged. Fair enough. I spend an hour removing the pain in the ass metal plate in the boot and remove the battery. Lo and behold, the battery is able to be charged after it has been removed from the car. What does this mean????

Ok, I bought a Projecta 4300mAmp charger, but when I try to charge the battery from either the bonnet terminals or directly on the battery terminals, the power light is on the charger but it is not charging.

The manual said that this may be the case if the battery is truly dead, and cannot be recharged. Fair enough. I spend an hour removing the pain in the ass metal plate in the boot and remove the battery. Lo and behold, the battery is able to be charged after it has been removed from the car. What does this mean????

Have you tried charging the battery in its original position with battery terminals removed? If it is not charging only when its connected up to your terminals my guess would be that there is a problem somewhere with wiring. I am by no means an expert so hopefully someone else here can give you some more info on where to look.

Good luck with it mate!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Was going to say the car pulls up nicely everywhere, especially going into that last long right hander before the main straight. Looks like a lot of fun.
    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
×
×
  • Create New...