Jump to content
SAU Community

Tuning Workshop

Jimbo2000

By Jimbo2000,
in New South Wales

 Share

Recommended Posts

T0nyGTSt Grand Master

T0nyGTSt

Posted
Posted

I think one thing to note is that tuning is something of an art, opinion, appraisal.

One tuner will always pick apart someone elses tune.

You go back to the original tuner, ask him about the apparent discrepancies and I'm sure there'll be some justification, excuse etc.

You can only go by people's past record and good word.

T.

Beer Baron Grand Master

Beer Baron

Posted
Posted

Does anyone know if the hitman will tune a factory ecu? (using a ROM emulator + chip burner?)

Got a daughterboard in my ecu and now with more mods need to get that baby tuned!

Richard

Jimbo2000 Grand Master

Jimbo2000

Posted
  • Author
Posted

hmmm i'm contemplating doing (what might be a silly move) and going with a somewhat unknown workshop/garage out at berowra, i've mentioned them before and have heard alright things from on here and really good things from outside.

had a chat to him a few weeks ago and was pretty convinced.

i'm just scared of the old saying you get what you pay for, (dont know what he charges anyway but it would probably be less than the bigger well known workshops) coming to bite me on the bum.... but then again if that was 100% accurate everone would have the exact same most expensive tune and others would be out of business

will keep you informed

sidewaymambo Mentor

sidewaymambo

Posted
Posted

The worse case is that you hanging over all parts you want them to put in, and discover later that they have been replace with something different..and you went back there and they denied..

Also make sure you don't rely on the simple dyno print out; number could be faked, unless it's done in shootout mode....

Mr R32 M-Spec Experienced

Mr R32 M-Spec

Posted
Posted

I don't have one (yet, maybe will get one)

but I would probably go to CRD, my friend works there and I Have heard numerous good things. had a couple of small things done and no problems.

other then that, I was chatting to a guy last night who has an S15 and has had it tuned by hitman a couple times and had no probs

mark

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • S1_C34
      Stagea Front CV Axle Question

      By S1_C34 · Posted

      I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • TurboTapin
      CD009 RB Conversion

      By TurboTapin · Posted

      Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Nightmare_mistress_R33
      CD009 RB Conversion

      By Nightmare_mistress_R33 · Posted

      Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
×
×
  • Create New...