Jump to content
SAU Community

Is Skyline Worth It?

cdw666

By cdw666,
in General Automotive Discussion

 Share

Recommended Posts

cdw666 Rookie

cdw666

Posted
Posted (edited)

okay, im contemplating getting a 1996 R33 Gts-t or a 1997 or 1998 Honda Prelude VTIR. The skyline seems to be misfiring a bit, but everything else seems good. It also comes with 1 year warranty (prob just mechanical). The skyline's done 99,000 kms, and the Prelude's done 170,000 km. The prelude seems to be running fine. My issue is that for the next one year, i need to choose the car that is not going to give me any problems what so ever. I prefer to have the skyline, as it is powerful and a very nice drive. However, I understand that skylines can be a bit of a money pit. I dont mind putting money into it after a year, but until then, i can't afford to do anything for it except doing its regular servicing and insurance. What do u guys think? Get the skyline with the lower Kms with misfiring but with 1 year warranty or the prelude with the high kms, seems to be running fine and no warranty? Thanks in advance.

P.S. i understand that as this is a skyline forum, you guys obviously have a love of skylines, but an objective, unbiased opinion would be appreciated :):(

Edited by cdw666
Link to comment
https://www.sau.com.au/forums/topic/245513-is-skyline-worth-it/
Share on other sites
Skyenate Collaborator

Skyenate

Posted
Posted

All cars are a money pit, not just Skylines :) Also unrealisitic to expect that any car will abide by your rule of not playing up for a year sadly LOL

Obviously get the Skyline though based on Ks if nothing else :(

gt-ahhh! Proficient

gt-ahhh!

Posted
Posted

its the same as anything really. my skyline has been a one nightmare after the other. but then again, my sisters barina is starting to fall apart now. and at least my cars a lot hotter and more powerful (when its working lol)

another thing you should consider is police attention. because that can be a pain in the ass also. and expensive.

GTR-N1 Grand Master

GTR-N1

Posted
Posted

Hi,

I've got both atm. I'm wondering what the 1 year limit is all about? Are you going o'seas; or do you have another car lined up in a year?

Because, if you're going to keep the car for just a year, and if the 'Lude is in good cond. I'd definitely get the 'Lude.

Why?

Because even if you get an aftermarket warranty on the 'Line, it won't cover the 100,000Km service unless you get that done as part of the deal!

Do you know how much the 100,000Km service costs?

If you get the 'Lude, you'll only be approaching the 200,000Km service by the end of a year and then you can let the next owner worry about that. My VTiR has just cost me $900 for the 200,000Km service (which included the hydraulic tensioner - a common replacement).

Now, lets turn the equation around a bit.

If you can wrangle the 100,000Km service as part of the purchase price, I would definitely take the 'Line. But sort out if that spluttering is in the engine or the 02 sensor, or AFM, or some other sensor etc etc.

As a RWD, it'll give you much more driver satisfaction over the 'Lude (FWD) even if it's the more expensive ATTS where on corners, the outside wheels rotate quicker than the inside wheels. The 5th gen 'Lude does not have 4WS unless it's a Jap import (JDM).

My 'Line (although it's a GT-R) uses 12l/100Km and 14l/100Km if stretched

My 'Lude uses about 9l/100Km as a daily

Hope this helps!!

Tez

Basti Grand Master

Basti

Posted
Posted

he graduates in a year. till then, money will be tight (as for all uni students) however with our course its very hard to work parttime and neither of us wants to put too much burden on our olds to support us. only difference with me is that i;ve already got my line.

charuth with wat you've told me, i'd say go for the lude. didja have a look at the white one?

  • 1 month later...
  • 6 months later...
  • 1 month later...
  • 1 month later...
  • 7 months later...
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • GTSBoy
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By GTSBoy · Posted

      That's hilariously putrid!
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
×
×
  • Create New...