Jump to content
SAU Community

Recommended Posts

it's either a 3037 or a 2835. And the sticker on the box says 3037 so i beleive it.

I'd trust the description and get it at that price to be honest. With the current exchange rate i reckon you could add another grand to the price.

3037 is good for 300rwkw or a touch over.

Thats a 3037 pro s kit ,same as i had.

GT-RS kit dosent come with dump or intake pipe etc etc, they only come with oil lines and compressor elbow, that could be a 2835 turbo as i cant see the exhaust wheel to be sure, but if you order the 3037 kit they will send you a 3037 turbo ofcourse, by the way i would snapp that up asap, they are good people to deal with to even if they are a little hard to understand sometimes.

hmmm is that where you bought yours from nizmo freek??

wow in us its a fair bit..how much did u originally pay for yours...what do you think of this turbo laggy much? do you have cam gears done??

how close to max are your 555cc injectors?? at 270rwkw

its a 3037 pro s

its good for around 300rwkw with a lil lag (read acceptable amount)

a gtrs will not get you 270 unless you have cams and absolutely ring its neck... 240-260 tops is about right

555cc injectors are good for a bit over 300rwkw on pulp

a 2835 pro s will get you 270rwkw and less lag

i run a 2835 and have 265rwkw on 20psi with exhaust cam gear to aid response, without the cam gear most people see 270-280rwkw

its a great turbo for the rb25 and i would highly reccomend it

its a 3037 pro s

its good for around 300rwkw with a lil lag (read acceptable amount)

a gtrs will not get you 270 unless you have cams and absolutely ring its neck... 240-260 tops is about right

555cc injectors are good for a bit over 300rwkw on pulp

a 2835 pro s will get you 270rwkw and less lag

i run a 2835 and have 265rwkw on 20psi with exhaust cam gear to aid response, without the cam gear most people see 270-280rwkw

its a great turbo for the rb25 and i would highly reccomend it

listen to what joey is talking about .....

so with cam gear and hp fuel pump z32 afm and injectors and exhaust....it will be laggy on my r34gtt? the gtrs kit that is??

and you suggest the 2835 pro s?

less lag in that turbo?

but as u said wont get much higher then 270rwkw and thats with cam gears ?

lag factor is essentially the same on both turbo's... a gtrs may his full boost a couple of hundred rpm quicker but the 2835 is a slightly bigger unit so when you his full boost on the gtrs and the 2835 is on 95% they are about even anyway and then the 2835 has a lil more puff left.

the lag factor is VERY minimal on mine.

basically my low boost (1 bar @ actuator) is what you'll get squeezing the crap out of a gtrs, so the 2835 is a little kinder to your car, albeit not as kind to your wallet.

gtrs = 250rwkw-ish

2835 = 270rwkw-ish

better of getting a gt3076r iw and you would save a couple of thousand at least.

exactly what i was going to say, i just got mine today and going to be installing it in the next couple of weeks once i get all the oil/water lines and piping sorted :rofl:.. btw paid $2k for the 3076R EW, exhaust manifold and dump flange.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...