Jump to content
SAU Community

Recommended Posts

Last week during a cruise on a freeway my R32 (RB20DET) all the suddenly started to sound like WRX - it got really deep sound, kinda like truck. and it became noticeably slower and its shaking like hell (there's no rattling noise or anything like that though)... First thought was faulty spark-plug, but then all the suddenly it fixed itself... It was alright for a while but then it started doing it again... It's alright at the moment but it's still happening at times, usually after driving for a while...

Should replacing spark plugs fix the issue or is it something I should be concerned about?

Link to comment
https://www.sau.com.au/forums/topic/247304-my-r32-sounds-like-wrx/
Share on other sites

hmmm... too early to celebrate. Today my car started making the same sound but only briefly. While servicing the engine I spotted 3 studs have snapped off the manifold. I'm planning to get studs fixed and replace gasket on the manifold as soon as I can afford... I just want to know if that might be reason for the weird wrx sound and temporary loss of power.

an exhaust gasket that is gone will make that noise but it will almost certainly be all the time,, not only every now and then.

yea... that's pretty much what I thought. And gasket is still in fair condition and manifold is not causing any problems at the moment eithers.

So it got much worse and it's pretty much doing it all the time now... It's really annoying so I want to fix it asap. I came to decission that's it's probably stuffed coil packs. Just cant afford to spend $600 on splitfires so I wanted to know what are more affordable options out there. 2nd hand stock coil packs?

Like blind elk said, try swapping your ignitor with a friends, Rok.

Still, you can't rule out the coils like you say. I found that the standard coils are actually pretty tough - mine were scorched, melted, and hammered - they weren't performing their best, so I taped them em up for a temporary fix, and they performed a lot better - got rid of some slight misfiring through rev range.

I bought a brand new set of superspark coils, installed, and found that they really don't perform a hell of a lot better (as they claim), than the standard ones taped up...

I reckon rule out the ignitor before you spend $ on coils

i garantee it will be the coil packs. it will be hard to find which one it is, but it will start getting worse and worse. what you can do is pull the cover off, let the car run until it starts to miss fire. then disconnect the coil packs one by one. with each one you disconnect the idle should get even rougher, until you disconnect one and the idle doesnt change. then you have found your faulty coil pack.

same thing has hapend to me with both my skylines. with my old gts-t i just replaced them one at a time as they went. but with my gtr i lashed out and got a set of splitfires.

i can highly recomend the splitfires. ive never had a problem with them.

hope this has been a help. :thumbsup:

Like blind elk said, try swapping your ignitor with a friends, Rok.

Still, you can't rule out the coils like you say. I found that the standard coils are actually pretty tough - mine were scorched, melted, and hammered - they weren't performing their best, so I taped them em up for a temporary fix, and they performed a lot better - got rid of some slight misfiring through rev range.

I bought a brand new set of superspark coils, installed, and found that they really don't perform a hell of a lot better (as they claim), than the standard ones taped up...

I reckon rule out the ignitor before you spend $ on coils

Yea... aftermarket coil packs making more hp than stock ones is pretty much just a myth from what I heard from many people. And as long as maintained properly stock ones should also last longer than aftermarket. The only exception is probably splitfires but even they are probably not much better than stock ones.

i garantee it will be the coil packs. it will be hard to find which one it is, but it will start getting worse and worse. what you can do is pull the cover off, let the car run until it starts to miss fire. then disconnect the coil packs one by one. with each one you disconnect the idle should get even rougher, until you disconnect one and the idle doesnt change. then you have found your faulty coil pack.

same thing has hapend to me with both my skylines. with my old gts-t i just replaced them one at a time as they went. but with my gtr i lashed out and got a set of splitfires.

i can highly recomend the splitfires. ive never had a problem with them.

hope this has been a help. :P

Thanks man. I'll try disconnecting them when I get time to see which one is stuffed and I'll replace it with stock one for now. :)

that happens sometimes because of slack connection. the result would be the firing of only 5 coils firing. the car will drive but with less power and the subi sound. the engine will become unbalanced hence unstable causing vibration

1. slack connection on the air flow meter. pins not making contact etc.

2. slack connection on one of the injector plug on

3. slack connection on the right hand side of the igniter (the end going to the plugs)

because current is flowing from pin to pin sometimes if not connected properly when the car shakes too much, it will happen and act back normal because of the arcing of the current flowing.

the best bet is when this is happening fly the bonnet and check connections one by one to see which one stops it. if you are able to use a 12 volt tester you can also check the connection to the coils itself. dont rule out any parts but i doubt those are any trouble. the muffler has nothing much to do with how the engine reacts in this situation. without the muffler the engine can feel and sound very smooth.

today i finaly had time to take off the engine cover and check the coil packs... after running the car and disconnecting one after another i found a faulty one, so its definitely a coil pack thats gone.

the only problem is that the replacement one I bought has different connector that ones found in my car. coil packs in my r32 are mcp-300 with three horizontal pins, while the one i got is mcp-200 with three vertical pins... which skyline uses ones with vertical pins?

have you considered a compression test on your engine?

Electrical issues, such as coil packs, may occur else where around the engine along the wiring. If you have read any of my post you will see my frustration in trying to find my WRX issue.

Good luck

  • 2 weeks later...

so the problem just got even weirder... the last possible suspect was fuel injector... so i had my mechanic to take it out and clean it. after that i started car and it was running perfectly. but then after 5 minutes it started missing badly again... so i unplugged the injector to check contacts, plugged it back in and car ran smoothly again so i took it for a spin again and after driving for couple of minutes it started missing again. usually starts in 2nd gear after 2,500 revs, but not while idling, no matter how high revs... so i unplugged it, plugged it back in and again car ran perfect for short time. After plugging injector usually car runs smoothly in 1st gear, in 2nd gear it starts stuttering a bit at 2,500 revs, and then same in 3rd and 4th and then after minute or two it starts misfiring badly again.

i just dont get it cause injector connector is firmly secured with the staple-looking thing...there doesnt seem anything wrong with connection because i tested it with multimeter...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...