Jump to content
SAU Community

Recommended Posts

  • Replies 719
  • Created
  • Last Reply

Top Posters In This Topic

Who cares if you can see the whole track or not from one vantage point? By that measure QR is brilliant, you can see the whole track from your pit bay. As a spectator, I'd rater see a couple of good corners up close than some speck of a car over the other side of the track that you can't really hear or see what its actually doing. That's not good spectating. Besides, you're never going to get too many people to spectate at Superlap. Its not as exciting to watch as head to head racing, and even State Championship rounds don't really pull crowds. Do it for the drivers who are paying the bucks to enter. The ones who are coming to watch will still come to watch whether its at EC or OP. Probably get less spectators driving out to Wakey rather than more.

i thought we established that noone likes to watch head to head racing here already.. rallies are time based, targa is time based, and superlap is time based.. and everyone loves them.

head to head has had its day... too many rules and restrictions.

and as a spectator... i agree... id rather see a good couple of corners than the whole track with its boring bits... i think e/c would be better because its a bit more manicured and looked after than op, its visually better than op with a better grandstand and view points.

op is 3.5 hrs for me anyway... wakey is out of the question unless i stay overnight there and for that... the event needs to be a bit better with the timeboards etc.

  • 2 weeks later...
  • 2 weeks later...

Well I actually bought some 2nd hand semis for them and then some good street tyres came up. Federal 595's. Almost brand new. They'll be my street rims so street tyres are better.

Troy... Hmmmm... Not yet.

  • 3 months later...

Picked up the latest issue of 'Motive' DVD during the week which has 90-odd minutes of Superlap coverage, some really good footage, well worth a look (and the thread bump hopefully!)

www.motivedvd.com for more info

I thoughts they planned on running two events in 2009? I hope they are thinking about two rounds next year. I hate to admit it but i think the second round should be held in either WA or perhams SA. There are some serious cars in both states that dont make the track to the East Coast....and would make good numbers for the event.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...