Jump to content
SAU Community

Rx7's...what May I Need To Know?


Recommended Posts

I found a car im keen to buy, BUT...i no nothing about RX7s!

All i no is they drink alot of fuel and need to be serviced every 10000kms or sumthng like that? and to service them is a pain in the ass lol

thats all i know hahaa..

Does anyone have any good pointers n tips for me, as this is all new to me lol

Link to comment
https://www.sau.com.au/forums/topic/247981-rx7swhat-may-i-need-to-know/
Share on other sites

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

As always there is going to be the typical negative rotary myths/false information/assumption answers (normally by people who have never owned one) when a question is asked like this.

I've had my Series 6 13B Turbo Datsun 1200 Coupe for nearly 4.5 years... The motor was rebuilt with a large extend port, GT35/40 turbo, no intercooler, water injection setup and has run 11.4/122mph and makes about 210rwkw.

The car has done at least 100 passes at the drags, been driven to Adelaide and back, driven around Tasmania in a week, thrashed on the street everytime it is taken out, countless burnouts etc etc and has only had the oil/plugs/filters changed in that time (servicing is piss easy, much quicker than my GT-R) with no engine problems at all (and this is from a un-intercooled motor as well).

It comes down to how well the engine is built, how well it is tuned and how well it is maintained. Like any performance car.

You are better off browsing www.ausrotary.com for much better information and answers to whatever questions you have.

I always thought Wankel Engines were more reliable due to their design, less parts, simpler, less things to go wrong....

In theory yes, but a lot more money has been put into design piston engines. Rotaries have other issues too, like seals and shit.

I actually don't know much about them either, but the design is just so much smarter, you can't help but be attracted.

My brother bought a brand new RX 8 and the Mazda dealer literally gave him a small bottle of engine oil and tell him to monitor the oil as the renesis engine will burn oil FROM NEW...

If that oil burning phenomenon has started to occur since the engine was new, imagine if you're buying a used RX 7, how good do you know the previous owner in maintaining the engine, and topping up the oil when needed ?

You never know.

Nevertheless they are great car, but you need to be prepare to maintain it properly, I mean this car is not some kind of an old corolla.

don't do it, think about when u want to sell it again, not many people want to buy RX-7s so it will make it that little bit harder for you to re-sell.

but ultimately if your keeping the car stock and you don't drive like Sam you will be fine as most problems arise after you start modifying them.

but the bottom line would be stick top skylines :banana:

you mean engine needs rebuild every 100,000Ks, and thats only the older fc's not fd models. someone correct me if im wrong

they look good but sound terrible.

It's actually the new engines that need to be rebuilt every 100,000km.

If it has been rebuilt make sure that it has been done by one of the better w/shops. Make sure the tune has been done properly, as the rotary's do not like any pinging and will break before you release your foot off the accelerator.

If the tune and build are spot on you should have no issues at all.

It's actually the new engines that need to be rebuilt every 100,000km.

If it has been rebuilt make sure that it has been done by one of the better w/shops. Make sure the tune has been done properly, as the rotary's do not like any pinging and will break before you release your foot off the accelerator.

If the tune and build are spot on you should have no issues at all.

I agree.

Next question is how many people in this thread have ever owned a rotary and how many are purely going off what they heard from a guy whos "dogs uncles aunt on there mothers side had a second cousin who maybe had one but it might have been a datsun 180b"?

Firstly i use to have a bridgeport 13b in an old rx7, i gave that thing hell, saw 10,000rpm many times and it never missed a beat, i also have 2 mates that have had/have a S2 rx7 with a S5 engine, purely standard engine with big turbo, fmic, ecu and they pumped out over 300rwkw, one of which is still running today trouble free the other blew a water seal so he decided to sell it as parts and buy a S6 instead of repairing it.

The S6 how ever was a bit of a nightmare, it was meant to have a newly rebuilt engine, after a few months he discovered it had blown a seal (dont know which one) so had stripped it down only to find that the plates had previously cracked and been welded up (once cracked they should be binned) and the housings had corroded from a lack of coolant, as he planned to keep the car he bought all new parts, i believe the cost was around the 7k mark, ever since then it has been perfect.

Another friend of mine built a S2 from ground up with an unknown import s5 13bt engine and got a mate to tune it, that blew pretty quick, he then got it rebuilt by a well known rotary wrecker, he didnt get 1000k's out of that one, rebuilt it again, got the same mate to tune it and never got 300k's out of it, today it still sits in his garage after having spent over 25k on it, moral of this one is to get a reputable workshop to rebuild it (not wrecker) and tune it (not a mate who thinks he knows what he is doing).

If you get a good one it will treat you well, you get some ones dog breakfast it will be a money pit, not that its any different for a skyline.

Ask for receipts for all work done and servicing, if it has a rebuilt motor get receipts and check to see what was done and how long ago, whilst these things have fewer moving parts and are theoretically simpler they must be put together with a lot closer tolerance than a piston engine and all that comes with experience.

Whilst all these experience's sound bad there not, if i had the money i would buy a S6, my gtst has 225rwkw and a host of mods, my mates S6 only has a fmic and raised boost and would blow my doors off, not to mention the smooth power of the twin turbo's.

And www.ausrotary.com is your best resource.

post-27276-1228642299_thumb.jpg

Edited by W0rp3D

Yep www.ausrotary.com is the best place for info!

I've owned 3 rotary's.

A RX2 with a 13b, then i destroyed it...then replaced it with a 12A Turbo. Then later i've owned a S2 RX7.

Rotary s are one of the most funnest cars that you will ever own.... after owing 2 modded WRX's, I'm still to find something as much fun as a 900kg 12A turbo rotary RX2.

Yes i did kill the 13b, but only because of my own fault! And the funny thing is even though i totally destroyed the rear gear, it would still start and move the car....sure it was very slowly and with a lot of smoke, but still it would move under it's own power! And the cause.... i didn't check the oil! :blink:

And my RX7 never missed a beat. I'd still have it, but you can't fit much more than the driver and a baby seat in the car.

It's very simple with Rotary's. Look after it and it will look after you!

It's the same with the new RX8's.... of course Mazda will give you some oil and tell you to keep an eye on the levels. Your not buying a Corolla here, the Rotary actually use oil in the fuel (a lot like a 2 stroke), to lubricate the rotor seals and apex seals.

It's very simple with Rotary's. Look after it and it will look after you!

It's the same with the new RX8's.... of course Mazda will give you some oil and tell you to keep an eye on the levels. Your not buying a Corolla here, the Rotary actually use oil in the fuel (a lot like a 2 stroke), to lubricate the rotor seals and apex seals.

True, they're like 2-stroke lawnmowers on steroid!

If your buying one, check it out when the engine is cold... the oil seals do take up a lot when they are warm. So starting a cold Rotary engine will revel a lot.... if it blows smoke upon start up for a few minutes, the seals are slightly worn, so you might need a rebuild in the future!

If it start's with no smoke (and i mean blue smoke for oil) you could have a good engine.

Oh and Rotary's are a lot of fun with compression lockups :blink: Also 1 thing with owning a Rotary... once you have one, it'll will never leave you. It will be in your blood, they have a way to get under your skin no matter how much you spend on it and how much might let you down. You will never have as much fun with a normal piston engine as you will with a Rotary!!!

For me, i sold mine and then had 7 years worth of WRX's.... but with a trip to Japan, do you think i could pass up a trip to the Mazda Museum??? That place is like the 'Holy Grail' for Rotary lovers!!! :D

lol thanks for all the info guys..even though one person says one thing and another disagrees...

im going to test drive one soon so ill see how i find it..

im still a little uncertain lol now im thinking an r33 gtr..complete opposite..but yeah who knows with me

lol thanks for all the info guys..even though one person says one thing and another disagrees...

im going to test drive one soon so ill see how i find it..

im still a little uncertain lol now im thinking an r33 gtr..complete opposite..but yeah who knows with me

:D:blink:

step it up a notch Ferah, GTT to GTR , its the way god planned it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...