Jump to content
SAU Community

Recommended Posts

  • Replies 72
  • Created
  • Last Reply

Top Posters In This Topic

also highly interested in a bolt on solution to twin rb26 turbos, as well as dyno or pics and specs

GTR turbos are easy we can put in ATR28SS 350HP CHAR for twin setup. Those are very very tuff little turbo made to handel high boost. Should get you 400rwkws with excellent turbo response.

GTR turbos are easy we can put in ATR28SS 350HP CHAR for twin setup. Those are very very tuff little turbo made to handel high boost. Should get you 400rwkws with excellent turbo response.

very interested, do you have an US dealers ?

Sorry we don't. But we can make them brand new and mail it over if you need. Had many US and Eurp customers lately as our dollar is sitting very low.

Edited by hypergear

I am interested in teting the rb25 bolt on hiflow for you when they are ready.

I can supply you with housings and fit the turbo to my car, tune it and publish the results if you are interested, I have been tuning rb's for a few years and am always interested in bolt on option.

cheers :O

im very interested in this as i am planning on doing it at the same time as a remap,

my car has the usual 'basic' mods (exhaust, intake, fmic, fuel pump, stock boost still)

will somewhere around the 220rwkw+ mark be acheivable with this high flow and a remap in peoples opinions (how much psi would i be looking at runninig out of curiousity to achieve that level)

also what other modifications (if any) would i need to support such power levels.

Edited by AFTDRK

220rwkws is very easy. The high flowed turbo should perform between 230~250rwkws. It should be archived around 18psi or less. By calculation it should archive peek out put of 450HP at 1.3Bar.

There are many dependencies, calculation is normally calculated based on 75~80% of flow capacity. and there are many things that we can do to increase the HP with the ATR28 CHAR in a restrictive environment, but it will results more lag.

The most common profile that we use for R33 high flow is ATR28G2 (400HP) and older G3(450HP) profile. The Current G3 (on the 282rwkws CA) requires a big turbine wheel which the stock housing doesn't seems to have enough meat to be machined out.

Thanks for answering questions etc.

However please be aware you are not a paying trader of this forum, of which there are a lot of businesses paying good money to advertise.

Talking about prices and so on from here must cease until such a time as you are a paying trader.

To become/purchase trader options, please see subscriptions under "my controls"

Thanks.

  • 1 month later...

hey guys, ive sent my turbine housing(not the core) to hypergear today..

ive bein talking to Stao there via email..since i live in perth

anyways..im getting my r33 series turbo high-flowed by them,,

i currently have fmic, pod, hks cat-back exhaust, walbro fuel pump, spitfire coilpack, greddy rs bov, apexi neo afc.

anyways, im just gona bolt this high-flow turbo straight onto my car..

its getting fitted with a ATR28G3 450hp core..

all for $800 :)

anyways my question to u guys is...

will i be able to drive/run my car since i dont have a aftermarket ecu, bigger injectors or a z32 afm..

but ive bein told by hypergear i can..

but 2 workshops here in perth say i wouldnt be able to drive or get my car running...

can some confrim this??

well, they said they can fit a 7psi actuator to it..

so i think im gona get that..

do u guys know what and how much boost i could run with the new turbo?

anyone else running a hypergear turbo on 33 with stock ecu and afm???

well, they said they can fit a 7psi actuator to it..

so i think im gona get that..

do u guys know what and how much boost i could run with the new turbo?

anyone else running a hypergear turbo on 33 with stock ecu and afm???

I want to see results on a RB20....

If the car's going to be tunned for power I recommend to use 14psi actuator so you can alter boost to 24psi. the 7psi actuator can hold a max of 10psi. So depends on further plans to the car.

Any word on using a ball-bearing core instead of the sleeve bearings you've mentioned earlier - and the extra costing around this? (If you're still allowed to talk about costings in public...)

With BB CHRA it will be a Garrett GT2871R or a GT3071/6R CHRA. To do that it will cost $1200AUD+ depends on the CHRA you want to put in it.

With BB CHRA it will be a Garrett GT2871R or a GT3071/6R CHRA. To do that it will cost $1200AUD+ depends on the CHRA you want to put in it.

I'm guessing the 2871 would be a more appropriate sizing for 220-250kw and ultimately quicker spooling and response?

  • 2 weeks later...
It all depends on what you do as calling it "high flow".

What we do is:

Re-profile both factory compressor and turbine housings.

Assemble profiled housings onto ATR28 450HP profile core assemble.

So basically its a brand new turbo with your factory housings for direct bolton purpose.

All ATR turbochargers are covered with 12 month warranty for performance usage.

I have been talking to this guy on NS.com.

So far prooven results with good internals.

gives gt2871r & 3071r garretts a fair run for money! Literally speaking!

For anyone who need rb20 stock turbos for rebuild "cheap as" feel free to contact my at [email protected] or 04218167564.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...