Jump to content
SAU Community

Help Needed By Someone Not Terrified Of Spiders


Recommended Posts

Short story, big spider actually huge spider in/on car, car needed to get to mechanic tomorrow evening...and well I'm not getting into it in fact I'm not opening my garage door...so hoping someone not scared of them can help with its transportation to mechanic tomorrow...I could bomb it to my hearts content(but its too soon for def death before booking with mechanic), I am that scared of them I dont know if ill ever drive the thing again..not for the faint hearted as its bloody massive and could be anywhere by now.

Im in narre area and can follow with another car...any help would be greatly appreciated...

Thanks in advance,

Dani

  • Replies 58
  • Created
  • Last Reply

Top Posters In This Topic

Where is your mechanic & what time does it need to be there?

I am in Pakenham & have the day off tomorrow... Gotta do some Xmas shopping, so I will be in/near Narre

Edited by iamhe77

I'm aracnaphobic and have had it happen to me several times. They seem to love my windscreen and then make their way inside the car through the front guard/door jam area, emerging right where I'm sitting :-)

Its that big I need a shot gun.

And like i said I could bomb it, but I honestly will not be comfortable driving it, and that means i have to get close to it..Im pathetic cant even look at spiders if I do, i have them all over me...those with the same fear understand...its horrible. I honestly have zero intentions of even going into the garage.

Iamhe77 I dont finish work till around 6pm its not due at mechanic until 7-7-30, mech is in oakleigh area.

ah-ha I have located someone not scared by the hairy pricks, ...much thanks to everyone...god help the poor bastards working on her when this baby decides to make an appearance...its as big as my hand....nightmares for a week I recon...

Cheers

too bad if it comes out whilst they are driving it...even those not normally worried I think will have issues with this one...esp if it landed and took up your whole lap area....ewwww farking things...I hate them..

couldnt be that big could it? I had a big hairy one that was about 7cm in diamiter spread out living in my car for 4 months. would crawl out of my engine bay and cross over my windscreen when im driving. Lucky for me I've got abit of a delayed reaction so I would notice it before it would register that is a big ass spider. My mate hated it and wouldn't get in my car which was all good cause he would drive instead..ha

You've nothing to be afraid of.

Random fact to allay fear..

The average human eats 8 spiders in their lifetime while asleep.

Some sources say up to 3 per year.

How many humans do spiders eat?

Did I help?

Edited by madbung

lol burn the garage...hahahaha thats a last resort, I did get a quote from a bugman $250...wtf, id rather burn the garage..haha

No seriously im saying massive...not so much its legs, but it had this huge ass body, granted I didnt hang around long enough to see it spread out...not the normal huntsman style, and no way was i investigating futher..I so should have taken a pic but i was shaking too bad to even call my boss to pick me up for work let alone take a picture!!! AS it was i had to crawl over the exterior of my car just to get out of my damn garage, quite obviously the spider had marked its territory on that side of my vehicle and the garage.

If im asleep and munching away on them...sweet if i happen to wake up mid way....I think id have a heart attack, and this thing was that big I'm sure it would amount to about 7 ppls quota.

Its that big I need a shot gun.

And like i said I could bomb it, but I honestly will not be comfortable driving it, and that means i have to get close to it..Im pathetic cant even look at spiders if I do, i have them all over me...those with the same fear understand...its horrible. I honestly have zero intentions of even going into the garage.

Iamhe77 I dont finish work till around 6pm its not due at mechanic until 7-7-30, mech is in oakleigh area.

You found someone to do it? No worries.

Just thought I would offer (I used to suffer from arachnophobia myself).

Best of luck!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...