Jump to content
SAU Community

Recommended Posts

  • Replies 155
  • Created
  • Last Reply

Top Posters In This Topic

i got my car pc.. the thing is smaller then 3 cd cases put together.. looks hot.. too bad ram is not upgradable but 256mb ram should be ok for a cap pc.. il only use it for the net when i am away from home etc etc

will have it installed and setup this weekend once i can workout how to stuff the hdd into there

i got my car pc.. the thing is smaller then 3 cd cases put together.. looks hot.. too bad ram is not upgradable but 256mb ram should be ok for a cap pc.. il only use it for the net when i am away from home etc etc

will have it installed and setup this weekend once i can workout how to stuff the hdd into there

Is that one of the single-din pc setups?

I didn't want to go so small (mine is about the same size as my amp) as it wanted it to be semi-upgradable and have room for a capture card.. eventually I'd like to have some good quality cameras throughout the car :P

  • 2 weeks later...

i see the anti-lag and rotary idle had them either running for cover or scratching their heads at Summernats.

http://www.vi-pec.com/forum/viewtopic.php?f=3&t=73

nice comment about it being all over the Power FC too.

we should have the engine monitor up and running soon for you to try with it also.

Edited by DiRTgarage
  • 2 weeks later...

I worked out how to setup Group N Anti-Lag and Cycle idle at Summernats, gave it a good work out, here is a video of my car spooling up 20psi of boost with the clutch in then dropping it (just a little burnout i was not keen to get kicked out)

Watch old mate to the left, he copped the extream anti-lag pressure from the side pipe and was jumping outta the way :laugh:

*More Vids of Anti-Lag*

I worked out how to setup Group N Anti-Lag and Cycle idle at Summernats, gave it a good work out, here is a video of my car spooling up 20psi of boost with the clutch in then dropping it (just a little burnout i was not keen to get kicked out)

Watch old mate to the left, he copped the extream anti-lag pressure from the side pipe and was jumping outta the way :laugh:

Uploading more atm

bloody yobbo's.

ahh paul you'd love it :laugh:

haha not really...only good thing about summernats are the pavillions + dyno.

glt toy....how much traction loss when launching anti lag etc???? is it very driveablewith the features + are they easy to turn off (rotary control, anti lag etc)

ahh paul you'd love it :(

haha not really...only good thing about summernats are the pavillions + dyno.

glt toy....how much traction loss when launching anti lag etc???? is it very driveablewith the features + are they easy to turn off (rotary control, anti lag etc)

Cycle idle is NOT anti lag, its for cooling when the car is on anti lag rundown, so when your not on anti lag the extra air and no spark in the cyl cools it down heaps, i noticed when idleing around with cycle idle the engine would not go to operating temp on a very hot day.. which is weird...

You can turn anti lag off with a digital input switch (but cycle idle stays on), and when my car is on 24psi with anti lag there is no such thing as traction what so ever. Its just a big show off thing i wreckon :( but its fun and grabs attention

its also kinda hard to drive the car with cycle idle.. its mainly for WOT driving so i will have it on again for power cruise.

Id be interested to see whether anyone has bothered to run the boost controller that comes with these computers. The guy whos retuning my car was part of the development team of these new ecu's and said they are incredibly good.

Wouldnt mind hearing some other opinions as naturally he is a tad bias!

Cheers

will let you know.. will be trying a stock r33 solinoid and the boost controll in the next couple of weeks.. hmmm i should do it tomorrow but i am lazy.

I'm using the boost control feature. I've got a Mac solenoid in place of the stock one. I have wired the ECU up to an external switch (factory fog light switch) for high/low boost :) The boost control seems to work fine. It's open loop though, which means it takes a little longer to tune on the dyno. It also has overboost protection.

There is a closed loop boost control feature coming soon I believe. I'm looking forward to that one.

this is prolly going to get laffed at, but since the vipec is just a board that you put in ur standard ecu is there a way to put it in your PFC and thats a way of possibly retaining the hand controller without having to go laptop..

this is prolly going to get laffed at, but since the vipec is just a board that you put in ur standard ecu is there a way to put it in your PFC and thats a way of possibly retaining the hand controller without having to go laptop..

No not possible at all.. however in a few weeks there will be a Vipec Dash available which will run rings around the Crappy padel power fc hand controller and have programable shift lights and all kinds of stuff available.

I will do a review on the Dash just before its about to be released.

will let you know.. will be trying a stock r33 solinoid and the boost controll in the next couple of weeks.. hmmm i should do it tomorrow but i am lazy.

Sounds great. I have an overboost problem at present and wouldnt mind checking out whether its teh boost controller thats causing the problems without buying an expensive new one. Solinoids are 100NZD (not sure about AUD) if you want a new one also.

Look forward to hearing how it goes mate.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...