Jump to content
SAU Community

Recommended Posts

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

i have a t67 i believe with a 8cm exhaust housing and have not been able to find a larger one to suit, you people with td06's do you know the exhast wheel size to compare, mine it 60mm from memory. Im not sure what to do atm as it will spool up nice and early with very little lag but not sure how much it will kill the top end.

Im not sure if the T67 uses the TD06H or the TD06 turbine, or another again. I have often read/seen ppl refer to the TD06-25G as the same turbo as the T67-25G, but there could easily be subtle differences, hence the different designation

What size are you after Clint as i have a 10cm and come the end of the week will know whether i want to go smaller, so may be able to trial fit one anothers and see how they go. I may even like to try the 8cm to see if i make the same top end power but with better response...perhaps telling me that my head, valves (???? i duuno) are more of a restriction then the exhaust housing on an RB20.

i would like a 12cm but a 10 would be ok too, thats why i need to find out if the TD06 has the same exh wheel, the blokes at MTQ said it was bigger than a TD06 and they couldnt find anything suitable in the misubishi range.

My engine is being done on a engine dyno so i dont wont to change it once fitted, so if i cant find something suitable i will just use it, can always add some extra power with Nos for the strip.

i think the 8cm is just another way of saying ar.. type thing.. just find out what a 8cm, 10cm, 12cm is equal to and there is your answer.. 8cm mite be .6 or something??? have a look at the ihi rx6 turbo.. very small exhaust housing but huge comp cover.. spools up at like 2800-3200 on sr20 but still packs enough for 300rwkw+ mite the same deal with your t67 with 8cm housing..

Dotn Apexi use a different convention again?

They typically have a P in front of their housing size referecne, which i think is the A/R in mm^2/mm, where as Garret use in^2/in so a Garret 0.87 equates to about the Apexi P22.

So how that helps me work out the Trust 8, 10, 12, 16 cm^2 housings i dont know ...anybody?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
×
×
  • Create New...