Jump to content
SAU Community

Recommended Posts

how many V8 supercars do you see with fully sick stretched rear tyres onto 11ty billion inch width rear rims?

how many rally cars do you see with stretched tyres?

how many F1 cars do you see with stretched tyres?

If it was any performance benefit these boys would be all over it before you'd even heard of it.

if we're talking about performance, then the right size spec tyre (near vertical sidewalls, if a little leant over toward to tread) will perform the best.

you don't see lambos, fezzas, porkers coming from factory with a 225 on a 10 inch rim, for a reason.

definately, but that has already been covered, no one is debating that. we are talking about whether its safe.

i know personally i have stretched over the years for drift, whether it be due to tyre availability or simply looking for tight, predicable sidewalls, never had an issue, but u will lose grip.

saying that, it depends on the tyre, if all ur running is cheap street tyres, then sometimes some stretch is better, over the years ive sometimes had street tyres on the front which have soft sidewalls, and found that stretching them a bit (225 on 9" kind of stretch) actually helped as it stopped the sidewalls from flopping around. saying that if ur running proper performance tyres with strong sidewalls, there is no need to stretch, and you will lose grip.

Dont stretch the tyres!

Get the right tyre for the rim. I will be using a 255 on my 9" rims on my Silvia racecar. So with 10's I would say you will need the 265's all round.

My RX7 racecar runs 225's on a 7" rim and that works fine.

You need some sidewall flex in the tyres, if you stretch the tyres you will find the tyres will tuck under and roll on the edges. The slip angles will also be reduced making hard to balance the car on the edge of grip and slide

Ashly

I've got 235/40 on my front 18x8.5's and 255's on my 18x9.5's. It works really well for me, only a slight undersize on both, which is not considered stretch.

I'd recommend 265/35's for you, or you could go 275/35's if you don't have guard issues.

definately, but that has already been covered, no one is debating that. we are talking about whether its safe.

i know personally i have stretched over the years for drift, whether it be due to tyre availability or simply looking for tight, predicable sidewalls, never had an issue, but u will lose grip.

saying that, it depends on the tyre, if all ur running is cheap street tyres, then sometimes some stretch is better, over the years ive sometimes had street tyres on the front which have soft sidewalls, and found that stretching them a bit (225 on 9" kind of stretch) actually helped as it stopped the sidewalls from flopping around. saying that if ur running proper performance tyres with strong sidewalls, there is no need to stretch, and you will lose grip.

thanks nisskid for staying on the subject whether its safe or not.

and thanks for the input guys im thinking of 255/35 all round or 255/35 f 265/35 for a bit more rear traction cos my 17/255/40 are just no good.also are staged size tires better for track or not as ive noticed a lot of front and rear being the same size on FR cars

i had 255/30 on my 9.5" rims on my 33 gtst and they were great.. stretched 235/35s for drift and it made a huge difference to the grip levels... the back end became all sorts of slippery.... for a track day... i say dont stretch the tyres.

i had 255/30 on my 9.5" rims on my 33 gtst and they were great.. stretched 235/35s for drift and it made a huge difference to the grip levels... the back end became all sorts of slippery.... for a track day... i say dont stretch the tyres.

hardly a fair comparison though, firstly i doubt they were the same brand and model tyre (might have been tho), 2ndly ur reducing the size by 20mm each size, of course ur going to have less grip, that doesnt mean the stretch was responsible for lower grip.

yes you're right, its not a fair comparo... what i should have said was.. drifting was much easier and more controllable with the stretched 235s as it felt much stiffer and more responsive in the back end.. that was without spinning the wheels until after the apex where power was starting to be applied and yes, the 235s had much less grip which made power oversteer much easier..

yeh a stretched tyre is much more tight, responsive and easy to control, hence why a lot of drifters that arent high level who get good tyres given to them (with strong sidewalls etc) use stretch with cheaper tyres.

as far as grip though, a 235 on a 8.5" and a 235 on a 10" would be a better comparison for stretch vs non-stretch.

how many V8 supercars do you see with fully sick stretched rear tyres onto 11ty billion inch width rear rims?

how many rally cars do you see with stretched tyres?

how many F1 cars do you see with stretched tyres?

If it was any performance benefit these boys would be all over it before you'd even heard of it.

if we're talking about performance, then the right size spec tyre (near vertical sidewalls, if a little leant over toward to tread) will perform the best.

you don't see lambos, fezzas, porkers coming from factory with a 225 on a 10 inch rim, for a reason.

its simple more width, more grip (with exceptions) and from what I understand v8 super cars, f1 and WRC etc run tyres with a stiffer side wall compared to a regular car or sport(road) tyre

Just out of interest in terms of the actual structure of a tyre, how does a semi slick compare to a normal road tyre, do they have stiffer walls, or are they the same, just diffrent compound and tread pattern??

cheers

elliot

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...