Jump to content
SAU Community

Recommended Posts

Did a firmware upgrade on the vipec that solved the misfire problem i was having a few pages back.

Went back for another tune it made 486rwkw on e85. Engine is rb26, -5's running 26 psi

Can any tech heads tell me how to upload the dyno graph as its over 2mb ??

Edited by Mark-32

I'll PM you my email and i'll do it for you if you aren't sure how to

Or, you can sign up with a hosting place like photobucket and host it there then use the IMG tags to embed into this thread

EDIT: Here they are

c7a59d33.jpg

473796fc.jpg

that is a huge number for -5's even on e85....

keen to know spec list too

I was suprised myself but I have dyno papers from when it was first run in on dyno on 14psi, then tuned on 21 psi on pump fuel, then now on E85.

All the dyno runs today were in 5th gear as 4th would just bag the tyres.

Spec list of what i can remember in no particular order is-

RWD Rb26 conversion in an r32gtst

r33 5 speed

hi octane 11 litre sump (rear head drain, nismo oil air seperator going into main catch can that drains to sump.)

1mm restrictor

2860 -5s

big trust intercooler (unsure of exact dimensions but its over 100mm thick and pretty huge)

exhaust is stainless split dumps into 3 inch y pipes into a 3.5 inch sidepipe no mufflers

cams are tomei 260 10.8mm lift??

nitto/je pistons

nitto I beam Rods

Arp stud kits throughout

balanced and blueprinted

nitto 1.2mm head gasket

vipec v44 ecu internal boost controlled

fuel system is 1v 044 lift pump

2x 044 external out of surge tank feeding hicas lines

greddy twin entry rail

aeromotive fuel reg

ID1000 injectors

post-71053-0-50326500-1340183038_thumb.jpg

Edited by Mark-32

Eyebrow's are raised by that result... Seems to be a bit on the generous side?!?

What would correction ratio be between AT 9deg and IT 21deg?

+1

With probably the strangest boost curve ever... And -5s hold 26psi @ 8000rpm without any drop off in torque!?!

This is certainly odd.

I assumed the figure was so high as its rwd only?

To begin with the boost was at 24psi but the boost curve flattened off aswel as the power curve around 6500rpm making consistant 430 odd rwkw.

The tuner asked if i was happy with that and I said i wanted to add a litte more boost at the end of the rev range to see if the power curve would continue upwards in the direction it was heading. He then snuck more boost into the engine up top and thats what happened.

Im stoked with it, haters are guna hate either way but it is what it is.

  • Like 1

The tuner said it was cylinder pressure that would kill the engine and it seemed as though it was struggling for spark as you can see from the dip in the power curve that looks like wheelspin after 5500.

The tuner had to adjust the boost controller in that way so it would run properly.

I have a crappy photo of the dyno screen from where he was adding more boost. It went 420 on 21ish then 460 odd on 24+ then made 486 up to 26psi

I just dont know how to upload it as its over 2mb. I can send it to someone if they can do it for me?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...