Jump to content
SAU Community

Recommended Posts

Hmm maybe if I go -9's from N1's I can get my 400kw :)

For the price it wouldn't be I guess just to chase 15-20kw..Probably wouldn't even notice it. Will find other ways for further response

HKS V-Cam 2.8 :D

For the price it wouldn't be I guess just to chase 15-20kw..Probably wouldn't even notice it. Will find other ways for further response

do u have a build thread on your setup as I'm keen to learn more about -9s?

What are u making with these snails?

^Have a friend running GT-SS at 310rwkw @ 18psi (RPM dyno) approx 90-92% inj duty cycle he said. Car has been tracked many times. Fuel system and AFMs are stock.

I have the tendency to go down the same route - retain stock fuel system and AFMs

But I'm concerned about the high injector duty cycle as my car unlike his will see some street and hills use with different temperatures and varying loads.

I also have -9, RPM cam gears, stock dumps, Mine's front pipe, 3" test pipe, 3.5" Tomei Ti catback and PFC.

So all in all, is 90% injector duty considered safe? Accounting for any spikes that may occur.

I know my friend's car is a pretty good example of it's reliability at that level, but would just like some opinions with other guys running -9's who run the car on the street and track as well.

Edited by RB2600

Well what captured my attention is 350kw from -9s...what does it take in terms of boost level and supporting mods to get to this number on 98 as I don't want to run e85?

Hi Nick (levinboy) - what power are u making with your setup?

Well what captured my attention is 350kw from -9s...what does it take in terms of boost level and supporting mods to get to this number on 98 as I don't want to run e85?

Hi Nick (levinboy) - what power are u making with your setup?

I'm making 350kw on 98 pump

Full boost at 3800rpm lower depending on weather, 22psi

Built engine still 2.6

Id1000s, Nismo fuel pump

im spinning out - great numbers there on 22psi :)

pm sent

I'd say, once again, attention to detail on the setup is where the better results are. Big, size matched exhausts blah blah.

Got a sheet Nick?

I run -7's with a shitty exhaust and stock afm's. With id1000's and a walbro 400 fuel pump I make 325kw on 20psi with E85. If I fix my exhaust and chuck some bigger afm's on I'd probably crack 350kw.

It'd be much easier to do it with -9's and I don't think there would be much more lag involved.

paul - u should overlay your graph with nicks, i wonder what the difference would be in response & what revs u have full boost

Here is dyno sheet

Tuned for response, hence the drop up top and my cat mainly being restrictive

8A48BB11-9718-4233-9092-94AC91FB0942-568

Will be retuning it soon with new cat soon :)

paul - u should overlay your graph with nicks, i wonder what the difference would be in response & what revs u have full boost

Ill have a play tonight. Need a calculator and a graph to doodle on.

Fkn speed. Put it in RPM farken!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...