Jump to content
SAU Community

Tricks To Get Into Evil Driveways With A Lowered Car

vidospace
 Share

Recommended Posts

vidospace Mentor

vidospace

Posted
Posted

OK so I stupidly went out and got a hot looking front bar for my R34 before getting my suspension done. The bar scrapes just a touch on my drive way no matter how I seem to turn the wheel. Once I was able to get in without scraping but I cant figure out what I did right! Now my car is back from the shop getting the SK kit fitted and it will be lower again (not by much but maybe 1 inch). The drive way is a dip basically. Our road is curved in the centre and then the drive way banks up over the pavement before flattening out in our property. So you can see my issue. Over speed bumps I know to go at an angle and all is fine but I need to know how to go at an angle and then when to turn back straight or opposite to get over such dips without killing my kit? Suggestions?

If worst comes to worst I might need to install a metal grill between the road and the drive way to even out the angle. But that might be overkill!

some_cs_student Veteran

some_cs_student

Posted
Posted

I have a very steep driveway so here's how I get in / out, but its only possible because my driveway is really wide, it can fit two cars side by side (nearly :yes:).

On the way out: drive onto the nature strip, reverse back on a sharp angle to stick the rear towards the road, then change it the other way full lock, I often do drive a little onto the other side of the kerb because the rear of the car is high enough off the ground. Sometimes forwards / backwards one more time to get the angle right and then gently across the road and it just makes it.

Getting in, completely different, I drive on the wrong side of the road because one side of the driveway is less steep then the other, turn late and sharp and the bar *just* makes it (and I"m heading straight for the wall so I stop, I then reverse and go in the 2nd turn :)

Every driveway is different, I've seen a few people make ramps (usually illegal under council law) and someone who had a WRX had a "cross over" built by his council (cost some serious $$$), another person got a free cross over made because she was near a council that did it for free :)

Personally I'm really tempted to pull out a ramp and drive onto it and take it away afterward.

Oh how lows your car? My one was 8cm from the ground when I put the Japanese suspension in, raised it to 13.5 and now its about 11.5 or 10.5 at the front bar...

Good luck!

bt23 Enthusiast

bt23

Posted
Posted

My one is pretty much sitting 10cm at the front and sides but the shape of my front bar sticks out at the lip which caused me a lot of grief during my first couple months owning the car (I had to eventually get it re-fiberglassed + resprayed). I still occasionally sand the paint underneath from scraping some driveways but nothing too drastic.

I live in a cul-de-sac with a very steep curb but mastered it by just keeping in mind to take a big angle. For some of the driveways with dips, you could also try reversing in. Some driveways you may just have to completely avoid altogether. It's just part of having a lowered car.

Hang in there...

P.S. There is no shame in getting a mate to step outside and check as you attempt to drive up. Sure, onlookers might think you are a wank, but at the end of the day you are saving unnecessary stress and money!

Phobic Collaborator

Phobic

Posted
Posted

just smash it up there and keep repairing the bumper haha, nah the best way is just go up it at an almost parrallel angle it helps when you have wide wheels that stick out the guards because they go up the curb before the bumper hits

vidospace Mentor

vidospace

Posted
  • Author
Posted

Well guys, got the car back today. Its about 1cm lower than it was before (just purrrrfect), and low and behold, it doesnt scrape AT ALL!

Guess the lower back end and harder suspension helped!

Swiper the Fox Grand Master

Swiper the Fox

Posted
Posted

i have the worst driveway in aust...an extremely steep twisting item that i have to put the Jeep in 4wd to reverse it up.

thats why i have a high ride height drag car not a gutter scraping circuit item.

some_cs_student Veteran

some_cs_student

Posted
Posted

Dirtgarage, that driveway sounds dangerous, for any non-4WD on my driveway you can't attempt to drive straight in without angle to you hear a scraping sound (in stock cars its often the rear).

videospace, glad to hear you got it in, I ended up getting my bar re-fiberglassed and re-sprayed and I've been very very careful since then...it wasn't really bad damage but enough scratches to get to me :)

joeyjoejoejuniorshabadoo Grand Master

joeyjoejoejuniorshabadoo

Posted
Posted
just smash it up there and keep repairing the bumper haha, nah the best way is just go up it at an almost parrallel angle it helps when you have wide wheels that stick out the guards because they go up the curb before the bumper hits

not if you run stretched tyres tho :)

Pezhead Grand Master

Pezhead

Posted
Posted

Have a look at the gutter and slope of the road. I put a thick board in the gutter and that gave me the 1" I needed to clear when leaving. Roads are purposely crowned to drain the water away to the gutters. For me the clearance problem was simply coming off the lip of the driveway into the gutter. That 1" drop caused the bar to drop down onto the slope of the road.

I got some 2" x 12" from the lumber store and put two sections out on the road.

I worked pretty well until the first big rain - I live on a hill.

Since then I've changed the suspension to put the car to only 1" lower than stock.

When I get on my other computer I'll show a picture of the driveway hell I went through. My driveway has a steep slope down and to keep the water at the top the previous owner created a sharp crest up then down. Everything bar my 4-runner got high centred on it. So it took a 2 weekends of kanga hammering and rebar cutting to remove the crest to a plateau.

Ah, what we do for the love of our cars.

Psymon Mentor

Psymon

Posted
Posted

I've just moved into a place with a driveway that a standard commodore can scrape its front bar on! I haven't tried with the skyline yet because it's still off getting work done but i'm not looking forward to it :blush:

elysium Enthusiast

elysium

Posted
Posted

i havnt even bothered with my driveway, Its narrow, steep and short and isnt even from one side to the other. my mate in a vy commo tore his muffler off coming into it, his is lowered a little but nothing compared to my gtr. my gf suzuki swift scraps front on coming down it and they are a short car...

ill have to post a pic one of these days...

iamhe77 Grand Master

iamhe77

Posted
Posted (edited)

I feel your pain.

Start on a 45 degree angle (pointed right), slowly bring it back to 45 degree left and slowly over the top rise.

I can have either my 2 dogs, or 1 passenger under 100kg in the passenger seat else I scrape exhaust tip on the bottom and the front pipe over rise (worse with 3" exhaust).

If I have a car load of people, they all get turfed at the bottom and have to walk up. 40C or 14C with hail = GTFO and walk up.

Part of the reason we are moving next week :)

Even my wife's Magna has been known to scrape and we had mates who were going to back their HiLux up, but couldn't clear the towball.

Edited by iamhe77
  • 11 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sinn3r
      R34 Skyline climate control unit transistor

      By sinn3r · Posted

      Hi all,   long time listener, first time caller   i was wondering if anyone can help me identify a transistor on the climate control unit board that decided to fry itself   I've circled it in the attached photo   any help would be appreciated
    • Kinkstaah
      Blue slip

      By Kinkstaah · Posted

      I mean, I got two VASS engineers to refuse to cert my own coilovers stating those very laws. Appendix B makes it pretty clear what it considers 'Variable Suspension' to be. In my lived experience they can't certify something that isn't actually in the list as something that requires certification. In the VASS engineering checklist they have to complete (LS3/NCOP11) and sign on there is nothing there. All the references inside NCOP11 state that if it's variable by the driver that height needs to maintain 100mm while the car is in motion. It states the car is lowered lowering blocks and other types of things are acceptable. Dialling out a shock is about as 'user adjustable' as changing any other suspension component lol. I wanted to have it signed off to dissuade HWP and RWC testers to state the suspension is legal to avoid having this discussion with them. The real problem is that Police and RWC/Pink/Blue slip people will say it needs engineering, and the engineers will state it doesn't need engineering. It is hugely irritating when aforementioned people get all "i know the rules mate feck off" when they don't, and the actual engineers are pleasant as all hell and do know the rules. Cars failing RWC for things that aren't listed in the RWC requirements is another thing here entirely!
    • GTSBoy
      Best place to order Authetic R32 Parts in Japan

      By GTSBoy · Posted

      I don't. I mean, mine's not a GTR, but it is a 32 with a lot of GTR stuff on it. But regardless, I typically buy from local suppliers. Getting stuff from Japan is seldom worth the pain. Buying from RHDJapan usually ends up in the final total of your basket being about double what you thought it would be, after all the bullshit fees and such are added on.
    • GTSBoy
      Ethanol Content Sensor - Always at 11%?

      By GTSBoy · Posted

      The hydrocarbon component of E10 can be shittier, and is in fact, shittier, than that used in normal 91RON fuel. That's because the octane boost provided by the ethanol allows them to use stuff that doesn't make the grade without the help. The 1c/L saving typically available on E10 is going to be massively overridden by the increased consumption caused by the ethanol and the crappier HC (ie the HCs will be less dense, meaning that there will definitely be less energy per unit volume than for more dense HCs). That is one of the reasons why P98 will return better fuel consumption than 91 does, even with the ignition timing completely fixed. There is more energy per unit volume because the HCs used in 98 are higher density than in the lawnmower fuel.
    • GTSBoy
      Blue slip

      By GTSBoy · Posted

      No, I'd suggest that that is the checklist for pneumatic/hydraulic adjustable systems. I would say, based on my years of reading and complying with Australian Standards and similar regulations, that the narrow interpretation of Clause 3.2 b would be the preferred/expected/intended one, by the author, and those using the standard. Wishful thinking need not apply.
×
×
  • Create New...