Jump to content
SAU Community

Recommended Posts

hey guys

pretty much the problem im facing at the moment is that...i have a kenwood dvd player and a JBL sub in the boot pretty much when im driving all good but when im stopping at lights and music is cranked up so subbies goin nuts lol (mirrors all shaking) the audio cuts out the dvd unit just turns off and then re load itself and turns back on and if i havnt taken off yet it just goes straigh back off as soon as the bass hits..but when i start driving again its fine..its like the battery cannot generate enough power to keep the bass going?

any ideas? been told to get our of those power supply thingos that look like NOS bottles lol

Link to comment
https://www.sau.com.au/forums/topic/254594-car-audio-turning-off/
Share on other sites

You have answered your own question.

Battery power is the most important thing for big bass, your amplifier is going into protect because your battery voltage is dropping below the minimum recquired for the amp to run ie approximately below 10.8V for most amps.

Upgrade your battery or install a second battery for maximum results.

Battery sugestions: Alco Batteries (thats what I use)

Yellow Top Batteries

Red top Batteries

Odyssey Batteries

Look for CCA level (cold cranking amps) 12V 400CCA or higher.

P.S It's all about the "BASS!"

yeah i had an inkling that would be the problem, however stupidly i listened to the guy at autobarn who told me no it cannot be the battery, you need one of those power holders or suppliers (NOS Bottle looking things)...he prob just wanted to sell me that and then when i come back and say it aint working he would say yeah now u need to upgrade your battery...grr why do i listen to them

heading out today to get a new battery thanks dude

dont asume anything!

Get a multimeter on your battery with the car running at idle with nothing else on like audio gear and take down some readings for voltage,then crank up your system to the volume you normally listen to it at where the problems happen and take down some more readings, Then post them all up here.

Jack

yep will try and get onto it...ive realised today its cutting out alot more because the air con is on clearly lol so drains even more battery power..normally it will only do it when theres massive deep bass average bass is fine but with a/c on it cuts out all the time but will get a multimeter and post it up thanks mate

also how big is your amp.. i had a massive sound system in my old car.. spent over 4g's.. and i used to pump it.. and it can cut off cause the amp is hot as! check cause there is only so much the amp can take then cuts off to cool down... i bought 2 heat sinks and the heat silicon to try draw some heat outta it and had two fans (amps were in custom install in wheel well).... one fan blew cool air in.. one fan blew hot air out.. gave me another 30-50min on playing time at high bass levels

also how big is your amp.. i had a massive sound system in my old car.. spent over 4g's.. and i used to pump it.. and it can cut off cause the amp is hot as! check cause there is only so much the amp can take then cuts off to cool down... i bought 2 heat sinks and the heat silicon to try draw some heat outta it and had two fans (amps were in custom install in wheel well).... one fan blew cool air in.. one fan blew hot air out.. gave me another 30-50min on playing time at high bass levels

hmm not very big but its not just the amp cutting out the whole headunit cuts out? could the amp cause that? i actually just looked at my amp and the fuse is pretty much melted and the fuse holder is all melted really really bizarre

OK from what you have explained I can tell there might be a few issues.

1. simpliest test Clean both your battery terminals use sand paper or a file. *Make sure Earth are well grounded to the body/chassis

2. Check your head unit wiring too make the Ground wire have good earth.

3. Make sure your Amp is well grounded too.

4. what size cable are u using must be atleast 8G and have atleast 50AMP fuse this will be fine.

5. check your alternator using a multi meter while engine running. atleast 13.8v to be decent.

6. The Nos bottle you're talking about is a Capacitor this baby are good for holding Power while u pounding away with bass. Mount as close to ur amp as possible.

see how u go

nothing to do with any of that. simply its the head unit's built in amp getting too hot.

Only way to avoid this is connect the rest of your speakers to a cheap four channel amp. My head unit used to turn its self off for the same reason, only difference is my head unit used to say "too hot" and would stop for a minute. Nothing to do with your sub or amp, but get a capacitor in the mean time to keep a constant level supply of power to your amp. in the mean time don't run your speakers at full blast untill you get an amp for the speakers or you risk destroying the built in head unit amp.

your spekers quality will start to get worse over the next few months depending how loud and how often you play it loud.

If it was a power supply problem you wouldnt have much bass at all, and your system will be run by distortion.

Jay if you want some advice from a installation technician that actually does this for a living please answer my questions and stop taking advice from "experts" on here, i know you mean well guys but please do not post if you do not know what your doing,you are just going to waste peoples time and money telling them to buy things they really dont need.

i had same prob as him EXACTLY and thats how i fixed it, amp and capacitor..... even if its not the head unit running too hot, my method of capacitor will fix it if its power supply prob. Either way i'm still right and I had the same problem as him exactly, this is how i fixed it, will work for him.

either way running the other speakers from a cheap external amp instead of the crappy inbuilt 18-20ish rms built in amp is a billion times better/safer/clearer than running of the head unit if he is going to pump the sound as often and as loud as he says he does, constantly stessing the head unit, in the end he will end up melting the kenwood amp in the headunit in time anyway.... i have already done this in a cheaper brand sanyo head unit, that didnt have rca's so i had to then change the whole headunit (cost more than a cheap amp) anyway.

and looking back at original post looks like its 99% chance your alternator is going to shit itself and/or your current battery is about to die. When my battery died when i had the capacitor connected to it i had no warning that the battery was old because the battery is in the boot (looks good clean and new), and no power problems untill there was NO acid left in the battery at all. The capacitor kept the car going as usual right untill there was no battery acid left in it. turns out the battery was a japanese brand battery that went broke and closed its doors in the year 2002 so the battery was super old.

More than likely it must be the battery because the alternator cannot produce enough amps at a specific time to handle a sudden power drain (from sub). The battery would take over for most of the power being supplied and the alternator just keeps topping up the battery and supplying extra power when the battery drops....

Altenator seems to be fine as it pushes the power through the system when the vehicle is in motion.

Most likely you need a bigger battery. But check your earths to make sure they are making good solid connection. Don't worry about a capacitor, that's like buying a second battery, the only difference being that it is solid state and can release all its stored energy almost instantly...

I think the best way is to get it inspected in person. Hard to find a correct solution if not enough info is given and it could be many possibilities that causes the the cut off. For god know could be a faulty unit ( knock on wood). But the way I have show you is to eliminates possible causes. IF you have wired the Speakers directly to your Unit. Then it is possible that the unit could over heat from high volume. Factory Unit inbuild amp is not that strong. Plus I dont know what size is your speakers or how many is hook up to the unit. Some unit come with inbuild thermo protection that cut out the power when overheating to save your Unit from melting up. When the unit turn off so will your amp. Unit have the remote wire link to your amp unless you have wired differently.

Incase of over heating then best way to solve is buy a 2 or 4 channels amp and use that to run the speakers 2 or 4 speakers and have the unit free of heat and produce better signal to the amp. *better sound from amp anyway , louder, stronger, clearer and more control.

good luck this is my last post for this topic.

Yeah Sorry We're not expert like some in here. cough cough... :P

Ok guys non expert packing up and leave.

I am packing up and leave now.

Edited by GTRBOYZ

Professional help needed :blush:

IMHO, seems like it is the battery.. If the amp got hot and turned off, why would that trigger the DVD player to turn off.

Im guessing you dont have a Volt gauge. Thats one of the first things i got when installing my system.

Do your lights start to dim when you say its "about to" turn off.

Capacitor will give it a constant feed, but you dont want to turn around and get one, and it doesnt solve the problem. Try another battery, borrow a mates one. Do the cheap things first .. so you dont just spend on useless junk.

MRXTCZ

Professional help needed :P

IMHO, seems like it is the battery.. If the amp got hot and turned off, why would that trigger the DVD player to turn off.

Im guessing you dont have a Volt gauge. Thats one of the first things i got when installing my system.

Do your lights start to dim when you say its "about to" turn off.

Capacitor will give it a constant feed, but you dont want to turn around and get one, and it doesnt solve the problem. Try another battery, borrow a mates one. Do the cheap things first .. so you dont just spend on useless junk.

MRXTCZ

headunit has a built in amp that when it overheats the head unit turns off and in turn makes the external amp turn off

  • 1 month later...

well i forgot about this thread and hadnt read the last few posts but in case you guys were ever wondering again...i took it to one of my strathfield stores and got em to look at it as my amp had f*ked up anyway i needed a new one

as you kno r33's have the battery in the boot and in turn the red battery/power cable going from amp to battery was full length never been cut so it was cable tied together which in turn i found out when it heats up the whole cable was heating and cutting the power off to the amp or something like that but as of now since we cut it back the amp & headunit had not cut off

although thanks for the help boys..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...