Jump to content
SAU Community

Recommended Posts

hi im new the site so please bare with me as i cant find any info on the topic yet. i got a 97 rs4 stagea and when i do a slow u turn the front of the car clunks and shudders in sync with one rotation of the tyre. im new to mechanics and dont know where to start. the clunk is worse in 4wd or when reversing. it shakes the whole car a bit and can be felt through the steering wheel. while driving straight or doing a standard corner its fine and is quiet as a mouse.

Link to comment
https://www.sau.com.au/forums/topic/254655-stagea-clunks-loud-in-the-front-end/
Share on other sites

Welcome Patrick,

Probably best to have someone look at it if you are not used to playing down below, could be a few things, CV, tie rods etc. Maybe go for one of those free 'safety checks', then get back to us with results.

Welcome Patrick,

Probably best to have someone look at it if you are not used to playing down below, could be a few things, CV, tie rods etc. Maybe go for one of those free 'safety checks', then get back to us with results.

I agree safety check is the way to go, but don't let them do the work unless your cashed up :(

Hi and welcome

If it is a heavy metal clunk and only there when on full lock I would put money on it being a CV joint. If you are not any good with spanners and things mechanical then it might be best left up to a mechanic to replace.

Phil

Mine used to do that too.

But only if I was in 50:50 mode. And only when I turned sharply slowly.

I dunno why but for some reason I thought it was normal.

Maybe someone told me it was. It was a few years ago so I cant really remember.

How often are you you using your 4wd lock button ? unless you have some serious slip situations, such as its snowing there or you live on the side of a grass mountain, not wise to use it. It will quickly destroy itself on hard surfaces.

sorry i havnt been able to reply in a while cos i was outta town. i might put it in for a safety check ike yous suggested. the tie rods/ends should be fine as i replaced them about six months ago. the problem was still there before and after. i also had the cvs cleaned up about the same time, apparently the boots were split but the cvs were fine so he cleaned them out and put some new boots on them. ive also checked tyre pressure and its fine. i also recently replaced the front stabilzer bar linkages which were worn. as for the 4wd use i rarely use it. maybe for 5 min or so every 2 months just so it gets some use. ill book it in for a safety check and let you guys know. thanks

are your tyres all good? Also, might be a good idea to have the Attessa fluid changed (you'll find the reservoir in the rhs hatch in the boot).

To change the attessa fluid can you just suck all the old stuff out of the boot compartment with an syringe. fill it to top turn car on and crack the bleed nipple under the car and then keep filling it?

i did the safety check and was told that the cvs were fine and so was the tie rods. he seems to think the rear difff locks and causes the clunk. as burkey said his used to do it so is this a standard thing or are we just special. i might change the attessa fluid to as most of the mechanics would probably miss it. i asked one and he couldnt tell me what the oil was for.

  • 2 months later...

i have tracked down the cause of the problem. the fluid in the transfer case was badly burnt and past its prime. the fluid in the rear near the hatch only activates the awd and it was fine. the oil i changed was in the centre diff off the side of the transmission. i used castrol transmax z and the shudder is all but gone. reading the manual a little bit of a braking effect is normal but the amount i had was pretty severe. thanks for your help guys

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Probably speedometer itself if the odometer is ticking. If the needle is stuck from a bit of grease or something that can cause it to stay at 0. Or a cracked solder joint in the speedometer can do it too.
    • Thanks Fella’s   to take this off topic and to elaborate a bit more. I have an rb25/30 going into a r32 GTST.. expected to make around 600-700hp. Would you?   A) R34 GTT box   B) CD00#?  I’ve seen a few posts about the CD swap and sounds fairly involved with making it fit etc but if it’s worth the work then I’ll go that way
    • Lower at the hubs. Funny I forgot to mention that part. Do this pull here I turned the camera off too soon but the graph shows a drop at the top and that was because the pipe from the turbo blew off. The tuner said we could’ve made possibly another 15 whp. He also added if I switched to ethanol we could up the boost some more as well. I was comfortable capping it at the most of 20 pounds. Turns out the turbo pipe just needed a new worm clamp. Got home replaced that then did a third gear pull from 3k to 7200 rpm and the power was great to the top. I just got an ecu mounting bracket from IEE that I need to try and get everything to fit well. It’s a PITA to get the harness and ecu fit properly behind that kick plate 
    • He means "as opposed to mechanical cable drive". Older cars (R32 for ex.) had cable drive. Later cars with essentially the same gearbox, ie R34 GT (NA RB25) used essentially the same box as the R32 GTSt, but instead of a cable drive, had an electronic speed sender plugged into the same hole in the box, running from the same little gear that would have run the cable. Some of the shittier later cars use a speed sender on the nose of the diff, or the ABS sensors.
    • Lower than engine, or lower than it should at the hubs? Either way, that is a nice power figure and I'm not surprised you say it rips now. What stopped you from turning it up any more? Injectors? Or did it just stop responding to boost?
×
×
  • Create New...