Jump to content
SAU Community

Recommended Posts

  • Replies 67
  • Created
  • Last Reply

Top Posters In This Topic

from what i know injectors run out around 270rwkw!

LOL!! On what fuel pressure are you basing that on?

Just because the car "seems" fine, doesn't mean it necessarily is, AFR's and knock count will tell the truth.

from what i know injectors run out around 270rwkw! and im not running standard fuel system , ive got Walbro 255LPH , SARD Rising Rate FPR set to 33PSI on idle . I checked the plugs today that i put in last week and they are running rich , they are kinda black all over the tip . Also it backfires like crazy off throttle. So i dont know the ARF's but i will definatly keep it on 11PSI now all i was saying is it works on stock ECU , might not be safe but everything runs sweet though ( from a driving perspective ) not mechanically wise im sure

That seems pretty low for stock idle fuel pressure (std runs more than that - I think 3 bar (45psi). Injectors on stock run out around 215rwkw - depends on what you mean "run out" cause they will keep supplying fuel just not enough. Not enough fuel with more air = KABOOOMMMM !!!!! Busted ring lands on 1 piston the absolute minimum (cost for basic rebuild at least $4000)

Obviously (for a physicist or engineer) flow rates and therefore HP of injectors are based at a certain psi - (the only way you could possible give 1 figure), but they ramp up with more psi.

You would probably get around 240rwkw at 1 bar with your setup if it was tuned properly. This can be done with stock injectors if you want to have them running about 65psi of pressure (above atmosphere). Now if you were a damn builder how much extra water would you put behind a damn built for say 215mega litres? Because you injectors are like a damn wall at this piont.

from what i know injectors run out around 270rwkw! and im not running standard fuel system , ive got Walbro 255LPH , SARD Rising Rate FPR set to 33PSI on idle . I checked the plugs today that i put in last week and they are running rich , they are kinda black all over the tip . Also it backfires like crazy off throttle. So i dont know the ARF's but i will definatly keep it on 11PSI now all i was saying is it works on stock ECU , might not be safe but everything runs sweet though ( from a driving perspective ) not mechanically wise im sure

band aid fix.

did you really think you could run a big aftermarket turbo with a stock ecu, stock ecu, stock afm and it would run good and make power?

do people not understand the idea of supporting mods; you can't make safe power with out enough fuel

from what i know injectors run out around 270rwkw!

my injectors were hitting 100% duty cycle at only 190rwkw on cold mornings. but you have an adjustable fpr so i guess you'll be fine..... :D

there is a world of

better response

better average power

better fuel economy

better overall

locked away in a new stand alone ECU or a complete remap

sure you can keep with the stock ecu and "it will work" but its not ideal

theres a massive difference between a complete tuned map and a piggybacked one

i was able to add in around 10deg+ on my std ignition map with the standard turbo

that drivability and how the car responds is amazing. this coupled with a complete turbocharger change, and youll have a pretty big difference

but piss and moan and keep with the stock ecu if you like

for the new guys reading, new to modifying your car this is how you smash your engine

buy a turbocharger kit thats much larger and plonk it on with std spec engine and std running gear

and expect it to work, turn the boost up and as long as its feels more poweful, its fine and nothing to worry

to upgrade from the std turbocharger to a safe a good setup you should have

stand alone ecu or remapped ECU (ask your tuner which one)

upgraded fuel pump (GTR is OK)

z32 airflow meter

injectors (500cc or higher, no hiflows)

clutch (heavy duty)

intercooler (any is OK, not SMIC, GTR is perfect)

a good competant tuner who can tune your selected ECU / remapped ECU

anything less is a comprimise and is likely to break the engine or put it at great risk

ballpark budget for this is at least $5k excluding the turbocharger

so if you think you can do it for $1200 go for it, but be prepared with "rebuild money" set aside

engines fail because

a) poor tune

b) lack of fuel, ie pump cant keep up, injectors maxing

c) no tune at all

d) owners screwing in more and more and more boost each time

e) excessive heat / detontation - poor tune, turbocharger working too hard, boost too high

yeah thats crazy, such a nice turbo but nothing to support it, you will need ecu and injectors then a tune and it will be fine, the way your running it, i cant see it lasting long, all it needs is the split second at higher revs for it to completly fail, will cost you alot more in the end,

ive just put a rb25 in my r32, i hate this R&R thing, it sucks, but im going to get a boost cut defender installed (apparently i can change volatage so i wont hit r&r), im only going to boost my car up to 13-14psi with this but i will still be putting it on the dyno just to be sure,

^^^

r&r is rich and retard. it's what the standard ecu does to protect the engine. adds more fuel and retards the ignition.

for the new guys reading, new to modifying your car this is how you smash your engine

buy a turbocharger kit thats much larger and plonk it on with std spec engine and std running gear

and expect it to work, turn the boost up and as long as its feels more poweful, its fine and nothing to worry

to upgrade from the std turbocharger to a safe a good setup you should have

stand alone ecu or remapped ECU (ask your tuner which one)

upgraded fuel pump (GTR is OK)

z32 airflow meter

injectors (500cc or higher, no hiflows)

clutch (heavy duty)

intercooler (any is OK, not SMIC, GTR is perfect)

a good competant tuner who can tune your selected ECU / remapped ECU

anything less is a comprimise and is likely to break the engine or put it at great risk

ballpark budget for this is at least $5k excluding the turbocharger

so if you think you can do it for $1200 go for it, but be prepared with "rebuild money" set aside

engines fail because

a) poor tune

b) lack of fuel, ie pump cant keep up, injectors maxing

c) no tune at all

d) owners screwing in more and more and more boost each time

e) excessive heat / detontation - poor tune, turbocharger working too hard, boost too high

and too much sand :(

for the new guys reading, new to modifying your car this is how you smash your engine

buy a turbocharger kit thats much larger and plonk it on with std spec engine and std running gear

and expect it to work, turn the boost up and as long as its feels more poweful, its fine and nothing to worry

to upgrade from the std turbocharger to a safe a good setup you should have

stand alone ecu or remapped ECU (ask your tuner which one)

upgraded fuel pump (GTR is OK)

z32 airflow meter

injectors (500cc or higher, no hiflows)

clutch (heavy duty)

intercooler (any is OK, not SMIC, GTR is perfect)

a good competant tuner who can tune your selected ECU / remapped ECU

anything less is a comprimise and is likely to break the engine or put it at great risk

ballpark budget for this is at least $5k excluding the turbocharger

so if you think you can do it for $1200 go for it, but be prepared with "rebuild money" set aside

engines fail because

a) poor tune

b) lack of fuel, ie pump cant keep up, injectors maxing

c) no tune at all

d) owners screwing in more and more and more boost each time

e) excessive heat / detontation - poor tune, turbocharger working too hard, boost too high

Very well said Paul. :(

dude, pretty much every1 here is saying the same thing to you. Its not because we think we're madk%^nts and don't want your car to be faster than ours, its because we have actually done research, had discussions with tuners/other owners and are generally well informed about the cars we have owned (in many cases for lots of years) and that we are passionate about.

We're only saying this for ur own good, so u don't blow a motor and end up having to folk out another 50% over the purchase price of ur car just to get it running again.

"You can take a horse to water but u can't make it drink"

+1 for sound advice in here, especially from the guys who've been around a while.

This thread makes me kind of scared now - I've got standard (i think) injectors with an aftermarket fuel pump and KKR pushing out 240rwkw, though the other day I did hit max cycle according to the microtech when doing a full throttle run in 3rd to program my Profec boost controller. Only happened once but it did give me a fright, might be some food for thought re getting some 500cc injectors, especially with my tune being rich as hell.

ok , here is one for all of you guys that said running a aftermarket turbo of the size that i'm running will not work on a stock ecu .. Not to piss in your pocket or anything but yesterday i decided to play around and just reset my ecu using the paper clip method and to my suprise it completly fixed everything i've been whinin about .. It now boosts FINE at around 15-16psi and pulls hard right to redline .. I've got no hesitation and no popping and everything is great car pulls harder then before and really has some torque .. I was at 220kw @ wheels with old turbo and i can really feel something around 250kw + .. Very suprised with my setup that everything that i have you guys deemed would not work but it does , i don't see the need to upgrade the air flow or injectors yet maybe for power later but i'm going good now , a power fc is my future upgrade but i'm happy with stock ecu and safc neo

lulz

from what i know injectors run out around 270rwkw! and im not running standard fuel system , ive got Walbro 255LPH , SARD Rising Rate FPR set to 33PSI on idle . I checked the plugs today that i put in last week and they are running rich , they are kinda black all over the tip . Also it backfires like crazy off throttle. So i dont know the ARF's but i will definatly keep it on 11PSI now all i was saying is it works on stock ECU , might not be safe but everything runs sweet though ( from a driving perspective ) not mechanically wise im sure

even more lulz!

injectors run out way way before 270kw mate, i duno where your getting your facts from

My stock neo injectors (370cc?) were maxed at 260awkw so wound the boost down and making 240awkw barely safely for now.

That seems pretty low for stock idle fuel pressure (std runs more than that - I think 3 bar (45psi). Injectors on stock run out around 215rwkw - depends on what you mean "run out" cause they will keep supplying fuel just not enough. Not enough fuel with more air = KABOOOMMMM !!!!! Busted ring lands on 1 piston the absolute minimum (cost for basic rebuild at least $4000)

It is a 3bar system but that doesn't include the vaccum or boost.. so 33psi at idle sounds about right..

my injectors were hitting 100% duty cycle at only 190rwkw on cold mornings. but you have an adjustable fpr so i guess you'll be fine..... :thumbsup:

RB25? wow..

looking forward to the next thread he creates

I just blew my engine = i am a f**ken idiot

+1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
×
×
  • Create New...