Jump to content
SAU Community

Recommended Posts

Hey Guys,

ok, i want to get the facts straight here..... half of the people tell me i cant do this, then the other half tell me not to listen and say i can do it.....

instead of ordering a new facia kit, one installer has told me he can cut out the existing bose system and make enough room for the double dinn.....

whats the go??

Link to comment
https://www.sau.com.au/forums/topic/256938-double-din-install/
Share on other sites

find another installer!

The easiest way is to get the correct panel and the correct AC controller and a pocket if you need one. the rest - bracket and top pocket/screen will carry over. if you like I can post images of the rear circuit board that covers the ENTIRE panel to prove otherwise. I will add to that the radio powers that panel.

you can do it yourself. But you just have to be patience with all the panel it needed to be removed. It'll take nearly 2 hours for me to install it myself.

But if you don't have the time then ask an installer to install it for you.

DON'T cut out the existing bose. It'll make it look stupid and your AC controller won't work.

You have no choice to get the Genuine Facia or get the Metra kit from USA, which fit nicer, but crappier AC buttons and cheaper too.

cheers

also - bose or non bose radio. if bose and you do not wist to remove the amplifer then you will also need the leads for that.

when you are ready flick me a PM. I keep most of this on hand.

essentially this is the main part you will need plus the leads and also a/c controller I believe

http://www.japanparts.com/images/ImageFrom...e=1&no=2818

at 11,600 yen from Japanparts.com excluding shipping, including other parts and labour is where the $600-700 comes from.

you paint it. OR you get the correct colour one. I paint mine.

as for your solution.

AC controller,panel, bose interface leads. all up a $900 exercise.

want it - ask.

Hello Guys...

Aeropro I believe sell this facia kit also. Has anyone been able to install the aerpro kit as per below?

I approached Autobarn to see if I can get one ordered in...costs about $500 and I believe it will retain the functionality of the A/C, however I haven't had the chance to get one yet as I am still deciding on what headunit/stereo setup I want.

FP997604left_grey.gif

FP997604.jpgNISSAN SKYLINE V35 350GT 03-04 (Infinity G35)

Replaces Entire Climate Control Panel and retains Full Functionality Of The HVAC System. Metra's patented quick release, snap-in, ISO mount system with a custom trim ring. Recessed DIN opening. Removable oversized storage pocket with built in radio supports. Also includes parts for installation of double-DIN radios or two single-DIN radios Painted to match factory color and texture Custom design allows retention of factory air vents in their original location Comprehensive instruction manual including step by step disassembly and assembly Includes all necessary hardware for a complete installation Contoured and textured to match factory dash

how to get the OEM double din kit? Chris, do u hv stock?

I just got my car.. dont like the audio... Can we connect aftermarket headunit to the original bose speaker and amp? Is what Chris said: "AC controller,panel, bose interface leads. all up a $900 exercise," the option tat i m looking for?

Thanks for this great forum... so much helpful people around~

I do have stock - want?

if so EXACT spec of your car. IE: A/C control,navi,bose?

actually fire me a chassis number. I'll do it that way.

here is it located? i can find vin, engine... but where is chassis?

will ask tomolo and pm u then~ Your $900 including install or??

VIN will do. take a photo of your drivers strut tower. the build plate is there and it will give me all I need.

$900 would cover the bits to make all of this work. you are not in brissy are you? (I travel but only if I haev 3-4 things to do in a city.) cost could well change based on the spec of your car (could be lower.)

I am in melb... *^@#$^&%

Will check the numbers tomolo, and pm u..

VIN will do. take a photo of your drivers strut tower. the build plate is there and it will give me all I need.

$900 would cover the bits to make all of this work. you are not in brissy are you? (I travel but only if I haev 3-4 things to do in a city.) cost could well change based on the spec of your car (could be lower.)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...