Jump to content
SAU Community

Recommended Posts

Top tank looks to be leaking, cracked or a seal-unknown as yet... am i better off getting a 300$ alloy rad? does this affect the auto trans as it will no longer be running thru the rad?

as i have been quoted more for a new top tank, seal and a cleanout than a JJR GTST alloy rad will cost.

standard trans cooler, but i think it just runs thru the rad to warm it up?

-Ryan

Link to comment
https://www.sau.com.au/forums/topic/257907-radiator-woes/
Share on other sites

Top tank looks to be leaking, cracked or a seal-unknown as yet... am i better off getting a 300$ alloy rad? does this affect the auto trans as it will no longer be running thru the rad?

as i have been quoted more for a new top tank, seal and a cleanout than a JJR GTST alloy rad will cost.

standard trans cooler, but i think it just runs thru the rad to warm it up?

-Ryan

Buy a second hand radiator from a stagea, I happen to know were to get one :P

Link to comment
https://www.sau.com.au/forums/topic/257907-radiator-woes/#findComment-4436829
Share on other sites

Top tank looks to be leaking, cracked or a seal-unknown as yet... am i better off getting a 300$ alloy rad? does this affect the auto trans as it will no longer be running thru the rad?

as i have been quoted more for a new top tank, seal and a cleanout than a JJR GTST alloy rad will cost.

standard trans cooler, but i think it just runs thru the rad to warm it up?

-Ryan

Your radiator place should be able to supply a bigger capacity radiator which has connections for the auto fluid. The point of going through the radiator is to bring it up to operating temp quicker - most trips are short ones.
Link to comment
https://www.sau.com.au/forums/topic/257907-radiator-woes/#findComment-4437558
Share on other sites

Your radiator place should be able to supply a bigger capacity radiator which has connections for the auto fluid. The point of going through the radiator is to bring it up to operating temp quicker - most trips are short ones.

that is what i was afraid of.

i've had enough, gonna try and get a credit card, fix all the small shit, and get another datto or something and pay off the loan with the difference... rare cars shit me, i was quoted 400+ IFF they can find a top tank

other idea is run a reco'd r33 gtst auto rad, think they are 10mm thicker

Link to comment
https://www.sau.com.au/forums/topic/257907-radiator-woes/#findComment-4437957
Share on other sites

The rad. i bought was a replacement to suit a stagea and the bonus was it is 25mm compared to std 16mm. It was 'brand new' at $450.00, alu. core. I had to sell my little left finger to pay for it. I have used rad. socks for years now. I took sock out today to see what it had caught. It had a heap of head gasket i had scraped and lost into water jacket plus some machining swarf. It came with rad. Prior post on head gasket story.

Link to comment
https://www.sau.com.au/forums/topic/257907-radiator-woes/#findComment-4438512
Share on other sites

The rad. i bought was a replacement to suit a stagea and the bonus was it is 25mm compared to std 16mm. It was 'brand new' at $450.00, alu. core. I had to sell my little left finger to pay for it. I have used rad. socks for years now. I took sock out today to see what it had caught. It had a heap of head gasket i had scraped and lost into water jacket plus some machining swarf. It came with rad. Prior post on head gasket story.

ouch

but not much more than i was estimated by a rad guy... where did you get it from? gen nissan with the auto hose thingo?

Link to comment
https://www.sau.com.au/forums/topic/257907-radiator-woes/#findComment-4438528
Share on other sites

Hope the half a job doesn't let you down. Been down that road a couple of times and found its not worth the money and time.

if it lasts me two months(when jayrad will have units in stock), i will be happy.

Link to comment
https://www.sau.com.au/forums/topic/257907-radiator-woes/#findComment-4448096
Share on other sites

Did you fit a 'Radiator Sock' when you put rad. back in? They save alot rubbish blocking rad.

crap nope, care to elaborate?

apparently the guy has bench and lab tested a LOT of coolants, and uses an organic(non-glycol) one, as it doesnt block the rad and has light cleaning agents in it!

Link to comment
https://www.sau.com.au/forums/topic/257907-radiator-woes/#findComment-4451558
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...