Jump to content
SAU Community

Recommended Posts

Hi guys, I posted this in another thread but it's a little obscure if anyone was wanting to find a how-to. I searched and found zip so thought I'd snap some pics of mine I did todday.

** I used two different size hole saws to cut the radii and simply used a cutting wheel to remove the rest. Lots of masking tape around the area to stop any damage from swarf.

Initially I mounted the pins, raised them a little to make contact with the bonnet and make a mark from inside. I then drilled a small pilot hole, and then masked on the template provided and went from there.

Measure six times, cut once I suggest! :thumbsup:

Made U shaped brackets to utilise an existing hole in the radiator support. The return down the front too to give some extra strength. Made these from 3mm steel. You can see I had to gring the bolt down a little to allow clearence.

22022001.jpg

22022003.jpg

This is the drivers side from under, nothing tricky really.

22022009-1.jpg

The passengers side was a little harder. I did this second to get the feel for it. This is a GTR bonnet so I hade to carefully remove some of the reo.

22022002.jpg

And the finished product! A bit of fine tuning is needed to get them just right, and it's very strong, not going anywhere. As a bonus the rubber stoppers they supply were the perfect length to allow a little preload so no rattles.

22022004.jpg

22022005.jpg

And a reminder that angle grinders with cutting wheels can bite.

22022006.jpg

Link to comment
https://www.sau.com.au/forums/topic/258154-aerocatch-bonnet-pins-into-an-r32/
Share on other sites

What a great read!! Came up really well...

I did the same thing 3 months ago, although mine is a fibreglass/carbon bonnet, so would have been easier to cut.

They work so well and look much cleaner than the old bonnet pin style..

Here's my finished result...

gallery_1569_106_158120.jpg

Was going to get my panel beater to paint them silver but he advised not to, paint might not stick properly and would most likely peel off from constant use...

Either way they're not as noticeable as the old bonnet pins, especially since it gets driven on the street...

i put these on my 32. the bonnet i used had all the supports cut out so i didn't have to make it fit around them.

the car also had had bonnet pins so i used the holes in the radiator support panel to fit mine but as you may have found it a bit to shallow under the bonnet to fit them so my bonnet which isn't real straight anyway doesn't quit fit flush. if i get a new bonnet i will install them the way you have.

oh and word of warning after a bit of work the lock in pins start to over balance and you need a tool to get them to lock down. i am not the only one to have run into this.

i got mine after seeing all the cars in targa tas last year with them and funnily enough your going in targa tas with some.

so these are regarded as street legal? Where did you get them?

yeah as they are flush fit on the surface of the bodywork most states accept these as road legal.

bensonmotorsports.com was the source for the woo... always in stock!

Nice one.

I have finally taken delivery of my carbon bonnet and a set of these bonnet pins.

I'm going to get Micolor to do it though as I would just mung it up if I attempted it.

Kudos to you for taking the time to do it yourself.

Regards

Andrew

Looks good, one of the more subtle ones which seems to suit the R32 better. How strong are the carbon bonnets with using Aerocatches. Is the carbon too rigid and brittle ?

No idea, it's got all the factory latches as well so it should hang together. the pins are only insurance.

great write up mate!

love these pins! so much tidier than the metal ones...

angle grinder = OUCH! hope your hand heals quickly...

I bought a set for my s13 a while back, but another "wooss" here

I took the easy way out (had my panel beater fit them while my car was in paint)

even he was nervous and he couldn't promise me a 100% guarantee on perfectly straight and flush fitment, but he nailed it first shot...

at first i was concerned they might bind up or become brittle, after sun/water/soap/dirt/dust etc but they are well made and with a tiny spray of wd40 stay nice and operable.

the only thing i could put them down for, is the pins themselves, they could be swapped out for some actual steel ones...

some pics from when i had mine done:

2008-03-12015.jpg

2008-03-28041.jpg

pins2.jpg

I tried to use some about 3 years ago but woosed out because i didnt want to cut up my GTR bonnet...maybe its time to second guess that decision :thumbsup:

lol, just bite the bullet Roy and do it mate, they look great and operate smoothly. I reckon they're the best part of the car now :D

Oh, guess what, the wheel Just turned up :D

If anyone needs it, i just made up a cutting/drilling template for the 125 Series, the one they supply is for the 120 series and slightly different.

Print it out full size and you should be sweet :(

Aerocatch_template.PDF

Ok, then where is the quickest and easiest pace to get them. Better shoot them off to the panel beater before the bonnet gets sprayed. Stuart?

They may look ok on my car since i am doing the fan boy black and silver thing :thumbsup:

Troy, got mine through revolution racegear, about $120 from memory....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...