Jump to content
SAU Community

Pedal Pads

LoNgStAr

By LoNgStAr,
in New South Wales

 Share

Recommended Posts

LoNgStAr Enthusiast

LoNgStAr

Posted
Posted

Hey guys,

I'm looking for some pedal pads to buy for my R32 Gtr. I've recently bought Carbon Fibre Sparco pads on ebay but unfortunately the clutch and break did not fit. :) had to post it back to the guy and got some refund off it.

If you have any suggestions on what to buy please let me know.

Cheers guys,

Long

Link to comment
https://www.sau.com.au/forums/topic/258535-pedal-pads/
Share on other sites
br3tt Mentor

br3tt

Posted
Posted

I fine my stock pads fine in my gtr.

I have seen some nice Momo ones, but they where pricey if I remember correctly.

If you do grab another set, make sure they have a bit of rubber on them (as it can be a defect for aftermarket pedals/pedal covers).

Link to comment
https://www.sau.com.au/forums/topic/258535-pedal-pads/#findComment-4445116
Share on other sites
N1GTR Grand Master

N1GTR

Posted
Posted

Standard ones.

Still havnt sen a set that looks any good, or more importantly, fits correctly and stays in place.

Dont forget the standard accelerator pedal has a kick out on the corner for down shifting, it would be stupid to lose that

Link to comment
https://www.sau.com.au/forums/topic/258535-pedal-pads/#findComment-4445375
Share on other sites
Kinks Grand Master

Kinks

Posted
Posted

why anyone would ever change their pedals is beyond me. the only time you ever see them is when you're standing outside the car (ie rubberneckers) and when you're driving your foot slips off because the aftermarket ones are invariably slippery metal, and highly defectable at that.

standard pedals!!! don't be a riceboy :D

Link to comment
https://www.sau.com.au/forums/topic/258535-pedal-pads/#findComment-4447515
Share on other sites
Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

where can you find standard pedals?

the _____ guy I bought my car off ripped off the rubber pads and attached w4nk spec razo pedals ontop, I went to remove them and found out THERE WASN'T ANY RUBBER on the pedals :banana:

Link to comment
https://www.sau.com.au/forums/topic/258535-pedal-pads/#findComment-4461389
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      RB25DE NEO with Haltech ECU

      By Kinkstaah · Posted

      For fuelling the Haltechs have O2WB fuel controllers. Very useful for helping tuning VE and correcting for *small* mistakes. Of course if your injector/cam/trigger/sensor data is just wrong (or for a GTT which is not a GT) then you will get impossible reactions to things. I am sure you know this already but the reason people don't typically put haltechs (or any Aftermarket ECU) on GT's is because there's practically no real gains to be had - So this knowledge won't be commonplace.
    • ChriscoDom
      Rear Sway Bar Busshings - Holden Astra TS (2002)

      By ChriscoDom · Posted

      Can someone tell me if the cracks seen in the rear sway bar bushings in these photo's is unacceptable from a roadworthy point of view?  
    • GTSBoy
      RB25DE NEO with Haltech ECU

      By GTSBoy · Posted

      Shouldn't need a "base map" for anything other than guidance to ignition tuning. You just need the engine capacity right, the injector size right, and something, almost anything, for a VE map. On an NA engine, fuelling is almost completely a function of load signal & rpm. It should run and drive with a completely flat fuel map. It will be too lean under load, but that's easily fixed. We used to tune all ECUs without any base map. There were no such things (until someone had tuned a near stock engine on one, and then they had a "base map".
    • Kinkstaah
      Duncan's V37.......race car?

      By Kinkstaah · Posted

      What did you actually buy/how much did it cost? When I got mine in like.. 2017...? 2019? the aim was to run Torque for gauges via ODB2 and things like Track Addict/Laptimers/Dashcam/Reversecam/Spotify etc. Mine never broke, but I wonder if you've got the same needs (it sounds like it). Cause I liked the idea of being able to do anything with it. That said, yours also cost 3x the cost of what I spent so... food for thought.  
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      For me there is a massive difference in manufacturer or big brand crippled android (Sony, Kenwood etc) vs the sort of thing I've installed here, which is basically just a tablet in DIN form factor with open Android, and the other model of course is mirroring - Android Auto/Carplay. I hate the locked down manufacturer and AA options where they decide what apps I'm allowed to install, including the Launcher but also importantly things like Ecutek (for this car) or Real Dash (Stagea) are not supported. Plus those crippled versions tend to be slower due to both overheads and lower spec hardware. On the other hand, when this breaks I'll likely be in trouble for support....but how is that different to owning an Infiniti anyway
×
×
  • Create New...