Jump to content
SAU Community

18x8+23 Wheels, Brembo Clearance And Dish

M I K E
 Share

Recommended Posts

M I K E Mentor

M I K E

Posted
Posted

my old wheels are still here and taking up space

18x8+23 all round --> sit the same as r34gtr wheels do on stagea :devil:

fronts have brembo clearance so great for 260rs also

no tyres

$800

in adelaide

post-36829-1235887330_thumb.jpg post-36829-1235887385_thumb.jpg

100_0628.jpg

and just for clarification, even though the specs of all 4 wheels are the same, the fronts have less dish because they are high disk and have better caliper clearance

  • 1 month later...
rasored Enthusiast

rasored

Posted
Posted

Hello, with these wheels how much more dose it make the car look like the front track is narrower ( which it is by 2.1`) and given this was the under steer better or worse with even more rear track added by extra width through more offset in outer rim , thanks

M I K E Mentor

M I K E

Posted
  • Author
Posted
Hello, with these wheels how much more dose it make the car look like the front track is narrower ( which it is by 2.1`) and given this was the under steer better or worse with even more rear track added by extra width through more offset in outer rim , thanks

i don't think you completely understand the dynamics of wheels yet..

ALL 4 wheels are EXACTLY the same in regards to diameter, width and offset

the difference in dish is due to the difference in disk type, ie allowance for brake caliper clearance

where did you pull the 2.1' from?

these sit 6mm in from r34GTR wheels, which is an INCREASE in track over standard

--

to answer RBPOWA's q, i'm currently running height/damper adjustable tein coilovers and it's sitting much lower than that at the moment haha

  • 2 weeks later...
=premo= Mentor

=premo=

Posted
Posted

Great wheels used to have a set strong and lighter than they look.... depending how heavy you think they look, but damn your stagea is sexc, love the body kit, stylish and aggressive.

PM replied to

  • 3 months later...
RS4S Newbie

RS4S

Posted
Posted (edited)

still for sale :(

someone buy them - bloody cheap for jap wheels in these specs and in this condition!!

Hi Mike

I cant pm you so can you send your e-mail to me as i have a few questions for you .

Thanks

[email protected]

Justin.......

Edited by RS4S

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      WTB R34 GTR Guard Liners

      By Kinkstaah · Posted

      Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • itsmeyo
      WTB R34 GTR Guard Liners

      By itsmeyo · Posted

      Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • Kinkstaah
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Kinkstaah · Posted

      You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • Dose Pipe Sutututu
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Dose Pipe Sutututu · Posted

      LOL.... you are correct there.
×
×
  • Create New...