Jump to content
SAU Community

Recommended Posts

hay just a quick one for you all....

i had this with my r32 as well (4wd). everytime i change the oil filter, it doesn't matter what i put under there or what i lose heaps of oil from it and it leaks all over the stuff below it and its really starting to shit me...

what do you guys do to not lose sooo much oil?

Thanks

curt

Link to comment
https://www.sau.com.au/forums/topic/259774-oil-change-question/
Share on other sites

even with a relocator kit - it can still be messy (I have a relocator in mine)...makes it eaiser to get the filter on and off...I always have a rag on standby for spillage as there is still some oil in the relocator

Here are a couple of photos of my oil cooler and relocation kit. Oil cooler on the driver’s side. Auto cooler on the passenger side

post-25786-1236238450_thumb.jpg

I found a couple of welded nuts in the chassis rail under the driver’s feet (aprox) and made up a bracket to suit for the filter

post-25786-1236238240_thumb.jpg

sounds to me like you've still got a rubber seal from an old filter on the block - the rubber o-rings can be left behind when you remove a filter so make sure that you take it off if it didn't come off with the filter. if you've still got an old o-ring on (without knowing) and have put a new filter on with its own o-ring then this will more than likely cause a leak. i'd check this before wasting money on a relocator at this point - it's not like the filter on them is exactly hard to get to..

oops kinda missread the original post :P

there will always be a little oil left in the filter even if you've drained the sump but not enough to worry about?

to answer the q about oil coolers:

they're fine for everyday use but be careful you don't run your oil too cool. ie if it's just a daily and you live in a colder climate i'd advise against it as the oil needs to heat up to thin out and work properly. a few of the guys i know that run oil coolers on daily drivers put bags over them in the colder months of the year to prevent air flow through it and then take them off when it heats up :laugh:

I did this yesterday arvo.

Have a greddy oil relocator kit so that it sits up above the fuel filter

Have a fujimoto oil drain release valve, so that its just a flick to release oil then flick back to shut off

Released the oil into old container - only 3750ml WTF?!

changed oil filter, changed spark plugs, then ran on only 5cyl so redid sparkies

filled with 5L Motol 3100V, then reset ecu

test drove revealed issue, redid as above all is great and ready for dyno run next week !

not using an oil cooler myself, just an Automatic gearbox-oil cooler

Yup i agree with what the guys said above, Drain the sump first & give it a fair bit of time before taking the filter off. I only witnessed a few drops from taking off the filter, from all the times i've done it.

Just have a rag handy :P

Undo filter a little, enough so it's not tight, get a plastic bag, cover entire filter with bag, undo the rest of the filter through the bag. Hopefully most of the oil left over in filter ends up in bag. Oh, and also a rag under the filter for good measure.

leave the filler cap or a breather hose off while draining oil, walk away for atleast ten mins before considering doing the filter(this is when i do my plugs) then change filter, fit sump plug and new washer(AW12), fill with oil

Undo filter a little, enough so it's not tight, get a plastic bag, cover entire filter with bag, undo the rest of the filter through the bag. Hopefully most of the oil left over in filter ends up in bag. Oh, and also a rag under the filter for good measure.

Huh? Why not use a drip tray?

Preferably one with a nozzle so you can pour used oil into the container that the new oil came in.

Agree with RBPOWA, drip tray under drain plug, release oil from sump, when finished draining re-position drip ray under oil filter, remove filter and drain into drip tray.

No mess, no fuss :banana:

Huh? Why not use a drip tray?

Preferably one with a nozzle so you can pour used oil into the container that the new oil came in.

Agree with RBPOWA, drip tray under drain plug, release oil from sump, when finished draining re-position drip ray under oil filter, remove filter and drain into drip tray.

No mess, no fuss :banana:

he means over the filter to catch those little drops that make ur engin bay look dirty... how much are oil filter relocation kits? the 260s is soooo much harder!

has any one used those new DRIFT filters? apparently they have a bolt on the back of them so if its too tight get a socket onto it and ur set!

Edited by chef_stagea
has any one used those new DRIFT filters? apparently they have a bolt on the back of them so if its too tight get a socket onto it and ur set!

So do the K&N oil filters, for about the same price.... and much higher quality (or so I am told by a mate who sells both)

yeah I usually do it as you both have described- but I think if your filter has an anti drainback valve this causes problems too - you will get a bit of spillage but not a massive amt

as above says XD drain the sump for good 10 mins :D then take filter off( a little bit will dribble ) then new filter sump washer and wash down sump and filter area new oil off you go :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...