Jump to content
SAU Community

Recommended Posts

Item: Purvis Eureka Kit car

Location: Sydney

Item Condition: Good

Reason for Selling: If it sells it sells if not i keep it. Don't really have time to fix at the moment.

Price and Payment Conditions: $5,500 WILL NOT DROP ANY LOWER, Not taking parts off to lower price, you take the car you take it all.

Extra Info:

Motor is apart, its a Vw 1500cc.

1.5" Bugpack Megadual Exhausts

Chrome Air filter

Lumpy Camshaft

Honed cylinders

EMPI Oil Cooler

Lexcen headlamp Covers - Bubbles in right side of Tint, will fix. Tint 35%.

Lexcen Smoked Side Windows - Custom made $400 new

Lambo Air Intake scoops

70's style side mirrors

Hydraulic Rams for Roof lift - New seals $100

Hydraulic pump for roof lift

Type R Wheel

Quick Release Boss Kit

Autotechnica Pedal Pads

Chrome Shifter

Monza Gearboot

Full Set of VDO Gauges

14" Bathurst Globe Rims (F:205/70, R:235/60)

VW 1500 4spd Transaxle - Has been flushed out

Valeo Heavy Duty Clutch + stock clutch

Valeo Pressure Plate + Stock P/plate

Short Shifter

Bilstein Gas Shocks

Rebuilt Front calipers

Brembo Front disk Rotors

Rebuilt Rear Drums

New Master Cylinder

Car Weigh's 780kg, with a nice paintjob and a 12A rotor it would go pretty good. New Floorpan has been welded in & painted.

All interior trim is there, wiring works, have all previous rego & engineer certs.

Car needs:

Motor: Either this one rebuilt - $1-2k, $200 ebay one or even your own motor you want to stick in.

Seats: Will Need to be from a smaller car - $?

and Rego: Car complies with all ADR's

Paint

For $3-4k you have a car worth $15k

Pictures:

Yep

Contact Details:

Pm me

In about two months time if it does not sell i will be putting in a Forged Vdub motor(ready for turbo), as of then price will be $8,500

post-29561-1236514395_thumb.jpg

post-29561-1236514522_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/260205-fs-purvis-eureka-f4/
Share on other sites

  • 2 months later...

Bump, motor has been rebuilt to standard spec(by my old man) but has not been put into the car or started. Price is $6,000, will also trade for a more expensive car + cash(upto $5000) your way if necessary. Prefer R33 Non turbo.

  • 2 weeks later...
  • 2 weeks later...
  • 11 months later...
  • 5 years later...
  • 1 month later...
Guest
This topic is now closed to further replies.


  • Latest Posts

    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
×
×
  • Create New...