Sammy34 Posted March 30, 2009 Author Share Posted March 30, 2009 Hey guys ust getting back now the mechanics been over the car the problem was turbo shaft play, aside from that engine is 100% running perfectly. YAY! Now to see some dyno charts the next few days Link to comment https://www.sau.com.au/forums/topic/260760-wird-turbo-sounds/page/2/#findComment-4508602 Share on other sites More sharing options...
bozodos Posted March 31, 2009 Share Posted March 31, 2009 You will be getting a new turbo though right Link to comment https://www.sau.com.au/forums/topic/260760-wird-turbo-sounds/page/2/#findComment-4508778 Share on other sites More sharing options...
Sammy34 Posted April 3, 2009 Author Share Posted April 3, 2009 KK so car got dynoed today 550cc injectors, hypergear hi flow and z32. Cars getting compressor surge... bad batch of fuel or poor dyno conditions. Car will get re dynoed next week in EFI performances new dyno cell with new fuel to try to correct the problem as the current dynob eing used for my car was poor conditions, Stale air etc. Just going to hafto wait till then Link to comment https://www.sau.com.au/forums/topic/260760-wird-turbo-sounds/page/2/#findComment-4516149 Share on other sites More sharing options...
SS8_Gohan Posted April 3, 2009 Share Posted April 3, 2009 what spec Hypergear to you use? Link to comment https://www.sau.com.au/forums/topic/260760-wird-turbo-sounds/page/2/#findComment-4516191 Share on other sites More sharing options...
Sammy34 Posted April 3, 2009 Author Share Posted April 3, 2009 (edited) what spec Hypergear to you use? its the larger rb25 hi flow with op6 rear housing, bush bearing or wahtever they call it, internally gated Edited April 3, 2009 by Sammy34 Link to comment https://www.sau.com.au/forums/topic/260760-wird-turbo-sounds/page/2/#findComment-4516249 Share on other sites More sharing options...
SS8_Gohan Posted April 5, 2009 Share Posted April 5, 2009 but you get to choose from a few different specs.. any of this sound familiar? ATR28? G2 profile, G3 profile? 71mm compressor wheel? 76mm compressor wheel? what rwkw numbers were you pulling during that initial run? Link to comment https://www.sau.com.au/forums/topic/260760-wird-turbo-sounds/page/2/#findComment-4518802 Share on other sites More sharing options...
Sammy34 Posted April 5, 2009 Author Share Posted April 5, 2009 (edited) but you get to choose from a few different specs..any of this sound familiar? ATR28? G2 profile, G3 profile? 71mm compressor wheel? 76mm compressor wheel? what rwkw numbers were you pulling during that initial run? its the G3 profile. As fo what numbers I made, I'll let you know when it gets re dyno'd as the main influences towards the bad tune atm are the dyno conditions and an extremely bad batch of vortex 98. It could be the manifold needs to be upgraded... not sure as of yet it all really jsut needs to be sussed out and have a good going over end of this week or beggining of next. The car only made 190rwkw's at 1.2 bar. And the timing is all out of whack atm. Edited April 5, 2009 by Sammy34 Link to comment https://www.sau.com.au/forums/topic/260760-wird-turbo-sounds/page/2/#findComment-4518992 Share on other sites More sharing options...
Sammy34 Posted April 7, 2009 Author Share Posted April 7, 2009 Hrm Im starting to wonder now. The hypergear turbos are able to run 20psi or so they say. Im starting to wonder if the turbo being internally gated and running 1.4 bar of boost could be causing the compressor surge. As I cant seem to understand how the standard manifold could be causing a restriction bellow 250rwkw's. Here are the turbo specs, my car mods and a small bit of detail on the first dyno and what seems to be happening atm. Hypergear hiflow ATR28 G3 profile .63 has the larger OP6 rear housing. Car has as follows: Hybrid FMIC AVCR boost controller z32 AFM Turbosmart Fuel Reg HKS Fuel pump Apexi Intake 550cc injectors 3" turbo back exhaust splitfires Nistune etc etc. So basic mods. Dyno run when I got the nistune donestandard turbo made 180rwkw'sat 13psi, everything was spot on. Now after the hypergear turbo, injectors and z32. its final power runs was set to 18psi, car was getting to around 250hpgetting compressor surge, overboosting and jumping to around 260hp at about 25psi. now the car had a bad batch of fuel in it I got earlier at a caltex, 98 ron of course. Dyno conditions were terrible as the dyno being used had no fresh air at all so the car hated it. Im getting the car re dynod to fix up the problems but have been told that the manifold may be giving the car too much restriction. But I find it hard that the standard manifold would need replacing at such a low power level. Link to comment https://www.sau.com.au/forums/topic/260760-wird-turbo-sounds/page/2/#findComment-4522380 Share on other sites More sharing options...
SS8_Gohan Posted April 7, 2009 Share Posted April 7, 2009 i guess it is possible. Might help if you're able to find out the compressor wheel size. how do you know you got the larger of the OP6 rear housing? looks like you've got all the supporting mods there, and i too agree that the manifold idea seems a little strange. when's the next dyno run booked? Link to comment https://www.sau.com.au/forums/topic/260760-wird-turbo-sounds/page/2/#findComment-4522395 Share on other sites More sharing options...
Sammy34 Posted April 7, 2009 Author Share Posted April 7, 2009 i guess it is possible. Might help if you're able to find out the compressor wheel size.how do you know you got the larger of the OP6 rear housing? looks like you've got all the supporting mods there, and i too agree that the manifold idea seems a little strange. when's the next dyno run booked? end of this week, beggining of next. Guys at EFI have bene a big help as there only jsut getting there dyno facility sorted out this week so there getting my car retuned for free as the other facilities were poor. As for the compressor wheel the guy from hypergear really didnt give me any specs to go buy, what I actually got in the mail was a turbo with a larger rear housing than what I ordered, sit the old turbo and new turbo side by side and u will see the difference. All I got from the bloke at hypergear was it was using to4 internals. I mite make a phone call and get the info right now. Link to comment https://www.sau.com.au/forums/topic/260760-wird-turbo-sounds/page/2/#findComment-4522414 Share on other sites More sharing options...
SS8_Gohan Posted April 7, 2009 Share Posted April 7, 2009 oh so you didn't send off your old turbo?? Link to comment https://www.sau.com.au/forums/topic/260760-wird-turbo-sounds/page/2/#findComment-4522431 Share on other sites More sharing options...
Sammy34 Posted April 7, 2009 Author Share Posted April 7, 2009 oh so you didn't send off your old turbo?? nah nah, they ordered 1 in and made it up. Bloke from hypergear recons its the intake pipe sucking shut, the boost solinoid is rooted, boost controller is rooted or cam gears. :S Link to comment https://www.sau.com.au/forums/topic/260760-wird-turbo-sounds/page/2/#findComment-4522460 Share on other sites More sharing options...
SS8_Gohan Posted April 7, 2009 Share Posted April 7, 2009 was OP6 stamped on the hypergear you got sent and OP6 stamped on your old turbo? Link to comment https://www.sau.com.au/forums/topic/260760-wird-turbo-sounds/page/2/#findComment-4522468 Share on other sites More sharing options...
Sammy34 Posted April 7, 2009 Author Share Posted April 7, 2009 was OP6 stamped on the hypergear you got sent and OP6 stamped on your old turbo? nope it had all been machined off. Link to comment https://www.sau.com.au/forums/topic/260760-wird-turbo-sounds/page/2/#findComment-4522484 Share on other sites More sharing options...
Sammy34 Posted April 7, 2009 Author Share Posted April 7, 2009 nope it had all been machined off. as for my old turbo, old turbo wasnt op6, but i did get the compressor wheel specs off stao. Front is .71mm, rear is .65mm Link to comment https://www.sau.com.au/forums/topic/260760-wird-turbo-sounds/page/2/#findComment-4522494 Share on other sites More sharing options...
SS8_Gohan Posted April 7, 2009 Share Posted April 7, 2009 those intake pipes do suck shut, that's for sure.... hmm... guess you won't know until it gets back on the dyno. did you have a specific power goal/figure in mind when you ordered the highflow? Link to comment https://www.sau.com.au/forums/topic/260760-wird-turbo-sounds/page/2/#findComment-4522525 Share on other sites More sharing options...
hypergear Posted April 7, 2009 Share Posted April 7, 2009 Its a ATR28G2 CHRA. using the GT2871RS Comp wheel. It might be in a None OP6 R34's rear housing. The comp wheel is not big enough to surge and we’ve opened up the air gap to avoid surging. Its been dynoed 233rwkws in smaller R33's rear housing at 1.1 bar. It doesn't seems to be a turbo issue. Check in take pipe, EBC, timing and tune. Link to comment https://www.sau.com.au/forums/topic/260760-wird-turbo-sounds/page/2/#findComment-4523269 Share on other sites More sharing options...
Sammy34 Posted April 7, 2009 Author Share Posted April 7, 2009 those intake pipes do suck shut, that's for sure.... hmm... guess you won't know until it gets back on the dyno. did you have a specific power goal/figure in mind when you ordered the highflow? Yeh around 250rwkw's but the tuner strongly believes its going to do better than that on his first impressions. we just hafto see I guess. Im going to be running 1.4 bar and if everything goes well hopefully if first impressions last I cans ee around 260rwkw's although thats probably stretching the abilities of my gearbox a tad as the cars auto. Going to get onto upgrading that intake pipe though this week, if anything Id say that sounds like whats going on as Im sure those intake pipes arnt made for running 1.4bar of boost Link to comment https://www.sau.com.au/forums/topic/260760-wird-turbo-sounds/page/2/#findComment-4523692 Share on other sites More sharing options...
SS8_Gohan Posted April 8, 2009 Share Posted April 8, 2009 look up the 'rev210 intake mod' if you want a cheap $5 diy solution. or these guys sell silicone intake pipes that are up to the job. http://www.racespec.com.au/ good luck and let us know how you go because i'm very interested in your final power and how that spec'd turbo goes. Link to comment https://www.sau.com.au/forums/topic/260760-wird-turbo-sounds/page/2/#findComment-4523844 Share on other sites More sharing options...
Sammy34 Posted April 20, 2009 Author Share Posted April 20, 2009 Im starting to wonder if my problem is being caused by my BOV hks ssqv, i believe there atmo bovs. Hrmm anyone with an idea? no one seems to be able to pin point where my problem is. I dont hear the bov sound anymore sinze the turbo upgrade... no pshhh just a dut dut dut dut dut sound when i come off the accelerator but i assumed that was due to running more boost. Link to comment https://www.sau.com.au/forums/topic/260760-wird-turbo-sounds/page/2/#findComment-4544587 Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now