Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

he was flailing the whipper snipper around like thor's hammer, whilst swearing in german and occasionally yelling in a strong accent "DON'T EVEN THINK ABOUT IT" sounding like Arnie gargling roof nails.

Sig'd.

Sig'd.

no more sammich quote?

two was too much to ask for :P

paid for fuel this morning. 163.9 is an all time high that I have paid for the litre. just over $80 to fill the golf, and I am pretty sure the 32 is nearly out.

no more sammich quote?

two was too much to ask for :P

paid for fuel this morning. 163.9 is an all time high that I have paid for the litre. just over $80 to fill the golf, and I am pretty sure the 32 is nearly out.

I paid the same last night...mega gayness

in other news

can some one open this link http://a2.sphotos.ak.fbcdn.net/hphotos-ak-snc6/190613_118765794865911_100001974734909_143505_436452_n.jpg

save the pic and upload it to this thread, work has all personal storage blocked and I am bored so I want to compare this dyno graph of -5 to my 2510s

no more sammich quote?

two was too much to ask for :P

sammich one vanished a while ago actually... it got too old :P

paid for fuel this morning. 163.9 is an all time high that I have paid for the litre. just over $80 to fill the golf, and I am pretty sure the 32 is nearly out.

I paid the same last night...mega gayness

I have 3/4 a tank of stale fuel in the 31, should last until I get back from melbourne :). Will put fresh fuel in for the tune.

I paid the same last night...mega gayness

in other news

can some one open this link http://a2.sphotos.ak...05_436452_n.jpg

save the pic and upload it to this thread, work has all personal storage blocked and I am bored so I want to compare this dyno graph of -5 to my 2510s

I saw that man, and Its a pretty nice power curve, but, I would say it's a little low. -5's are 720HP worth of turbo.

Interesting it makes 10- 15 more horse power every where until it pulled away right at the end. Running lots more boost though (about 7 psi more!)so that might have smothing to do with it.

I saw that man, and Its a pretty nice power curve, but, I would say it's a little low. -5's are 720HP worth of turbo.

Its probably not a terrible result for him, it was done at the same tuner as me and his dyno is a bit of a low reader...as evidenced by all the sad faces at the dyno day the club had there! lol

I saw that man, and Its a pretty nice power curve, but, I would say it's a little low. -5's are 720HP worth of turbo.

I think you'd be doing really well to get 600hp+ out of -5s. The highest I've seen is 430kwish which is about 560hpish? I want to see someone throw a set of those new efr turbos on a 26 or 26/30. Would be a bitch piping wise but I bet they would crank out some solid numbers with epic response.

I think you'd be doing really well to get 600hp+ out of -5s. The highest I've seen is 430kwish which is about 560hpish? I want to see someone throw a set of those new efr turbos on a 26 or 26/30. Would be a bitch piping wise but I bet they would crank out some solid numbers with epic response.

yeah twins on a GTR never seem to be able to hit thier combined rating, mine are rated a 310hp each...but are no where near that, infact people are amazed that i made what I did at the boost level I am on so yeah my 620hp turbos are flat out making 450 at the engine

Yeah I don't think it's as simple as I have 2 x 400hp turbos so I should make 800hp. Either way -5s seem to be the go to turbo if you want 400kw and still keep the twins.

Yeah I don't think it's as simple as I have 2 x 400hp turbos so I should make 800hp. Either way -5s seem to be the go to turbo if you want 400kw and still keep the twins.

sadly there doesnt seem to a be a lot inbetween somthing for 300awkw like a GTSS/ -9/2510 or 400awkw like 2530/ -5...though it would seem like the 2530- -5 are quite capable of matching at least the 2510 for response so just running them at less boost could fill that gap

Yeah, Twins never hit their advertised theoretic and neither does a single, although it does come alot closer, there are always loses, heat,drive train etc etc.

Are you talking about mercury, I was there for that dyno day a couple of mates had their cars run up.

I made 431HP on R33 N1's on my 32 at ~17PSI I would like to make more then another 36HP with a few hundred horsepower more of turbo on board.

Not to take anything away from that result, because that thing would go like a bat out of hell !

My N1's are busted now (oil seals) so -5's will be going on and shooting for 400AWKW.

See how I go i guess.

Today I made Craig do work. Was lulz :cool:

Yes i did have to work hard for that lol. The strange thing is that you will get more $$ for that sale than i will lol.

sadly there doesnt seem to a be a lot inbetween somthing for 300awkw like a GTSS/ -9/2510 or 400awkw like 2530/ -5...though it would seem like the 2530- -5 are quite capable of matching at least the 2510 for response so just running them at less boost could fill that gap

400awkw seems to be on the really well sorted motors with all the fruit to back it up + running 25psi lol. Most results on the -5s are 340 - 380kwish and yeah the response is pretty good aswell. You could get -9s and run E85 and go for 350kw lol.

Yeah, Twins never hit their advertised theoretic and neither does a single, although it does come alot closer, there are always loses, heat,drive train etc etc.

Are you talking about mercury, I was there for that dyno day a couple of mates had their cars run up.

I made 431HP on R33 N1's on my 32 at ~17PSI I would like to make more then another 36HP with a few hundred horsepower more of turbo on board.

Not to take anything away from that result, because that thing would go like a bat out of hell !

My N1's are busted now (oil seals) so -5's will be going on and shooting for 400AWKW.

See how I go i guess.

I think he is referring to EFI at Yatala. -5s will be sick.

just be sure to keep going back to the same dyno to measure differences

and don't be disappointed or disillusioned if the temps and humidity is different on different days

most dynos have compensation to power depending on weather conditions

to give you an example of how different dynos can read;

roughly same temps etc, just different brand/model dynos (GTST 33 GT30 @ 19psi);

Matt Spry = 312rwkw

Mercury = 336rwkw

Allstar = 301rwkw (with wheel spin)

Godzilla = 331rwlw

So it was impossible for me to tell how much power I was making as it depended on which dyno we used...

all i know is it was 300rwkw+ :D

400awkw seems to be on the really well sorted motors with all the fruit to back it up + running 25psi lol. Most results on the -5s are 340 - 380kwish and yeah the response is pretty good aswell. You could get -9s and run E85 and go for 350kw lol.

Yeah i am considering E85 at some point. taking my boost up from 15psi and running E85 would get me pretty close to 350 as well i reckon!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
    • OK, if it idles at 1000+ with the AAC, its not an idle airflow problem. The cold start valve just gives extra air when the engine is cold, but you have enough air without it to idle at 1000. I think you are back to a fuel problem, sorry. Can you see the fuel pressure staying constant or does it drop as the revs drop to a stall?  
×
×
  • Create New...