Jump to content
SAU Community

Recommended Posts

I'm after anyone running a HKS GT-RS on an RB25DET, (genuine HKS kit, not a Garret equivalent) to post up their dyno graphs.

Specifically their boost graphs.

I'm running one on my car and have been for some time, but only recently 'finished' the package off with injectors and a Z32 AFM...

It made 253rwkw on 18psi, but boost isn't holding in the top end, which is why I'm after other's GT-RS graphs, as well as any similar experience with boost not holding, and how you overcame it if you did...

My car has all the supporting mods, with most mods being Jap brands and not cheap chinese copies.

Thanks in advance :)

Link to comment
https://www.sau.com.au/forums/topic/261410-hks-gt-rs/
Share on other sites

do you have an electronic boost controller? Honestly every dyno graph I've seen I always seem to see the boost pressure starting to drop off at the top end mine included. My tuner said that it's very common for skylines. I'm sure someone will disagree and probably has more useful advice.

How much is the boost dropping off and how quickly ? Post up your dyno graph if you have it handy

Link to comment
https://www.sau.com.au/forums/topic/261410-hks-gt-rs/#findComment-4481180
Share on other sites

I am interested in this as mine is also dropping off albeit on GTSS on a 26, but the same question ponders, I am going to replace the EVC6 to see if it is defective failing which I will wind up the HKS actuators to set them at 14 psi (currently at 11) so the evc only has to hold 4 psi above the actuator pressure rather than 7.

I hit and about 18ish for say 1,000 rpm and then as with the above, it tapers off a couple of psi down to low 16's.

Link to comment
https://www.sau.com.au/forums/topic/261410-hks-gt-rs/#findComment-4481941
Share on other sites

I have the same problem as well, it peaks at like 19psi then falls to like 17psi, no matter how much I stuff around with the duty cycle settings.

I thought my BOV was leaky, so I put a rubber sheet between the stock BOV & the cross over pipe, no difference. I thought it was the actuator, but after seeing dyno graphs, it seems to be the norm.

Link to comment
https://www.sau.com.au/forums/topic/261410-hks-gt-rs/#findComment-4482166
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
    • Sorry, just assumed that talk of coloured pads meant EBC red/green/yellow/shit stuff. I don't know the DBA pads, but it's a reasonable bet that they will be OK. DBA make good stuff generally. Those 4000 series rotors I linked to are very good. I may well replace the RDA rotors I have with those when required.
    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
×
×
  • Create New...