Jump to content
SAU Community

Help! Hicas Light On, Power-steering Gone!


Stitch
 Share

Recommended Posts

Im suprized no one has told you to run the hicas diagnostics, i carnt remember how to do it from memory but it was very simple, do a search for hicas diagnostics, its a trip, it does all this weird crap and the rear wheels turn left and right slightly and a code flashes up on the dash, the hicas light will flash the code exactly like the ecu diagnostic mode does. Im pretty sure that the car is suposed to be off the ground and level before running the test because the rear wheels turn left and right.

From memory i think i had to do the procedure a few times to do it right because if you dont turn the steering wheel to the right degrees left and right it wont register properly and wont put it into diagnostic mode.

Hope this helps ..

Link to comment
Share on other sites

  • Replies 92
  • Created
  • Last Reply

Top Posters In This Topic

Yes as i said its a hard thing to get into, you have to be very precise, it took me quite a few times to finaly get into it, just keep trying, i swear it works ..

Link to comment
Share on other sites

thanx for he advise on diagnostics, looks like this doesnt work on alot of early model r33's im guessing the ones that experience this issue very often.... it would be good if hicas diagnostic could be done from the ecu tiself (turning the little knob)... otherwise stop trying the steering wheel method it doesnt work with ours

Link to comment
Share on other sites

Hey as far as i know this test works on all R33's

I have an aftermarket steering wheel and i still got into it, but it took quite a few trys, here is a tip, go a little further when doing the steering wheel to the left and right at whateva the angle is ..

Link to comment
Share on other sites

Sup guys,

New to forum and got a GTR a few days back, been reading up alot on the site about things and there is a great deal of interesting information.

To add to this thread, I'm have the same problem, but mine is because I have no speedo (assuming speedo cable is broken).

After a few k's the light come's on and the steering becomes heavy.

Working with plant machinery, I assume the power steering pump provides hydraulic pressure to the Hicas pump. Because the Hicas disables (for whatever reason) the solenoids in the Hicas system close off, adding a lot of pressure (and stress) to the power steering pump.

I wouldn't focus on the power steering pump for the cause of your problems, but it's merely a side effect of the Hicas system becoming disabled.

As some others have said, a new steering wheel could be causing the issue. For me it's no speed sensing. Not knowing all of the sensors the Hicas system uses, but assumingly steering, speed, and possibly individual wheel speed? (ABS sensors).

The diagnostic system (mentioned above) would provide the you with the cause of the problem. Being very new to it all, I haven't had the chance to double check if mine's what I think it is.. ..But yeah, I doubt 'the cause' is anything related to the power steering.

Cheers.

Link to comment
Share on other sites

Diagnostic does not want to work for me at all. Mine is an early model. 1993. Those saying it doesn't work on the older models appear to be right, unless I'm doing something wrong but I've tried it about 10 times now. Contact cleaner on the plugs and sockets did not work, the earth straps in the rear look suspect, I will try those next.

Link to comment
Share on other sites

  • 2 months later...

In relation to having trouble getting into the diagnostic mode, i have had trouble getting it activated as well.. Is it possible that the car being converted from automatic to manual would stop you from getting into diagnostic mode??? as there are 2 different procedures for auto and manual.

Link to comment
Share on other sites

  • 2 weeks later...

I had the same problem in mine, so I installed a HICAS lockout bar.

Problem came back this afternoon (1 month later) so I removed the HICAS fuse from the boot.

Seems to be good again, fingers crossed it stays that way. :)

Link to comment
Share on other sites

  • 1 month later...

Hi all,

I also had problems with my HICAS with the light coming on after start up but would go away when you turn ignition off then on again once car warmed up. This occurred around 6 months ago. In the last 2 month the HICAS light would suddenly come on during driving and the steering would go heavy. Any who, it ended up being the HICAS control module. I replaced a leaking capacitor and cleaned up all the corrosive liquid on the PCB. Car is a 93 R33 gts-t. Been a week with no issues as of yet. Hopefully I will never see the light come on agin.

Also, the diagnostics doesn't work on this first release R33. Must be firmware related.

Hope this helps..

Buy!!

Link to comment
Share on other sites

does the HICAS in the R33's even use the PS pump? I just took one apart, and the HICAS was fully electric it seems. However in my 180sx, the HICAS was mechanical (used PS fluid). I locked my 180sx hicas and removed all the hicas junk, and looped the lines back together. HICAS is a PITA.

I would suggest just locking/removing the hicas! use this as a good excuse :cool:

Link to comment
Share on other sites

  • 3 weeks later...

LOL, mine even work more funnier.... my light comes on everytime i turn off my car, i have a turbo timer in her and when the time i shutting her down the turbo timer seems like doesnt work in 0.5 sec and come back on...? i just scared if it stuff my turbo up.

Link to comment
Share on other sites

don't know about the skylines, but my 180sx HICAS kicked in at 80kmh, no lower. funny cause it would snap to full (hicas) lock in one direction (it was stuffed) as soon as it "activated" so at 80kmh i got a nasty rear end wiggle.. then i had to drive like a crab... hence take that shit out.

Link to comment
Share on other sites

  • 4 weeks later...

i am having the same prob as well.. i am driving a gtst 33 the car can just turn off when the hicas light is on and the steering wheel will be heavy.... any solution about this???

Edited by akajonz
Link to comment
Share on other sites

All of you guys need to check your wiring, especially your main earths. That was the problem with mine. If your earth wire is secure, try adding another one somewhere on the chasis. A voltage drop will cause HICAS to cut out and sometimes power steering, I am not sure why but all other electrics work fine. Good luck.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • Got some decent progress after work yesterday and also today. Got the ECU all wired and passenger side interior all back together. Kept the wiring up nice and high to avoid people standing on it. Got the surge tank relays rewired and tidied up the pump wiring and cut a hole to bring the cables through.  I found a spare USB cable I had lying around so I decided to cut it up and see if I could use it for my CAN 1 bus. Turned out one of the pins I needed was to the shield of the cable so i cut it up and desoldered it and resoldered to the correct pins.  Had the issue with the powersteering hose hitting the A/C compressor and fan shroud. I pulled the bracket off and modified it to remove the front mounting point which now clears it all. Will keep an eye on it to see if theres any signs of fouling once it's up and running.
    • That's some good input mate. Nice.
    • So today I went well outside my comfort zone (again) to replace my valve cover gasket.  I have had a big leak over the exhaust leading to a lot of smoke and smell every time I drove it. The leak was in the rear driver's corner.  The job wasn't hard as such, just a bit finicky and time consuming.  The old gasket was rock hard and broken right where the leak was.  The leaky corner had so much sitting oil in it.  The good news to my amateur eyes was no buildup or sludge under the cover. It all looked fairly nice in there.   I haven't started it yet. I ran out of light and body when putting the coils and injector loom back in. Probs only 30min left for the morning.  I was so nervous putting the cover back on, I must have lifted it 5 times to make sure the gasket was still seated properly. God it's going to be nice to be leak free and not make other traffic light queuers think my car is about to explode.
    • Gave the Mazda it's first wash, it will need some clay, a light compound, and polish polish to remove a few swirl marks, but that will be a job for when I have a full day to get my DA polisher action on
    • Just did this job on my 32 with the boost doc kit. was quite simple to fit, hardest part was getting the rubber bungs back on the firewall. does anyone know how the heater will work now without the flap in the bend? Will I just have a heater on 24/7 now?
×
×
  • Create New...