Jump to content
SAU Community

Recommended Posts

Some update pics:

Exhaust modified for Tech Edge Wideband AFR controller insertion

84209660.jpg

Tech Edge:

20863560.jpg

-5 Back turbo bolted in

54873105.jpg

19895316.jpg

Both -5s bolted in:

55665202.jpg

64159670.jpg

OS Giken Cam Gears

40810107.jpg

Fuel Rail, injectors, FPR, Vipec, oil catch can, cam gears, belts etc all going in today/tomorrow.

Dyno Saturday

  • Replies 219
  • Created
  • Last Reply

Top Posters In This Topic

Hi Bakes

Are you using one large pod to feed both turbos? I can see a y peice in one photo but it might be something else in frame.

Twin HKS pods. The Y piece you can see is the HKS pipe that goes to the front mount. From the Y the piping splits into two lines to each turbo.

Hi all...just got home

All the turbo's, piping, air filters etc done.

All the fuel system done.

Vipec install done.

Full service done (except coolant as radiator is still out)

Techedge controller wired in and connected.

Bloody balancer bolt is tighter than a fishes alibi...i have a special impact wrench that puts 600ft/lbs of impact torque through the bolt...no love. Have to drop the car down on its wheels and try the old 5th gear, handbrake, footbrake and 1mtr length of pipe over the end of the breaker bar method tomm.

mate with your set up you will push 330rwkw no probs, I have GTSS's and all the other goodies and am running a very safe 436rwhp at only 16 psi.

Proves that if you spend the money on good gear in a well thought out combo you can make good, safe power without throwing gail force winds down the 26's throat

Sounding better and better everyday... just got a nice cheque in the post here so looks like mine will be complete soon too :laugh: Clutch goes in next week then tune on Friday :/

Best of luck, I'm sure you are itching to get her back

New back turbo in place with all piping etc back in:

57192988.jpg

New front turbo in place with all piping etc back in:

10416492.jpg

Hypertune Billet Fuel Rail in with Siemens 750cc Injectors:

80919117.jpg

Turbosmart Fuel Pressure Regulator:

12632613.jpg

OS Giken Cam Gears in Place:

91055736.jpg

Gates timimg Belt, Oil Catch Can, Trust Clear Cam Cover to go in this week.

Dyno Tuning on Saturday.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...