Jump to content
SAU Community

Recommended Posts

  • Replies 65
  • Created
  • Last Reply

Top Posters In This Topic

Very nice - one question though

Do Vicroads code the non-custom number plates to coincide with the model of the car, or is it just coincidence that I have only seen plates starting with WHC on R34 GTRs - three of them now.

Very nice car!

Thanks for your opinions guys. Yeah i am very happy with it. Cant wait to go on another great ocean road cruise, havnt been on one for ages.

Same here... will be doing so when I get my car back from it's rebuild :woot:

Hey mate how are ya? Yeah finnaly got one, give me a little whilE then ill race ya lol. Love those nismo rims, cant wait to put them on my NUR.

Your car or ya dads car..? LOL!

Doesn't matter as least you got one!

Yeah Nismo LMGT4 is a must for the Nur.

Well you know the basics of what to mod for a Nur, let me know how you go!

Thanks for your opinions guys. Yeah i am very happy with it. Cant wait to go on another great ocean road cruise, havnt been on one for ages.

You should join us on the member cruise! Would be great to see another 34 GTR in the mix, especially a Nur :P

Although not sure if it's too late to get your membership for that event.

You should join us on the member cruise! Would be great to see another 34 GTR in the mix, especially a Nur :P

Although not sure if it's too late to get your membership for that event.

It's never too late...You can join on the day if you really need to leave it that late...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...