Jump to content
SAU Community

Recommended Posts

Why am I hearing that to register a vehicle with an aftermarket FMI, or at least a vehicle that isn't fitted stock with a FMI, you are required to have an engineer's certificate?

The list of PDF files StinkyPoo linked to in the Turbo Timer thread didn't seem to have anything relating to air-intake of the engine, be it Turbos, Superchargers, pod-filters or anything...unless I missed it lol

Anyone got anything solid on this?

Link to comment
https://www.sau.com.au/forums/topic/263430-front-mount-intercoolers/
Share on other sites

i was told that you could only have one intake mode.. ie pod filter or intercooler.. not both. if you have more than one you need to get it engineered.

im not saying that the above statement is correct, that is what i was told but the engineer

i got my pod filter engineered because i had to do my coilovers so i thought i might as well do that too. i also got my pedals and boost gauge engineered

That's what I've heard also...So if the only engine mods on a car I'm looking at are FMI and Turbo-back exhaust, it *should* be ok? :wub:

Also, by "engineered" you mean certified, or (re)fitted by an engineer?

Approximately how much that cost?

Thanks

Edited by Trozzle

Yeh, I don't think many cops would pick on you cos it's soo easy to remove a FMIC. Anyways, here is the section of text:

1.1 MODIFICATIONS NOT REQUIRING CERTIFICATION

• Fitting a replacement new, used or reconditioned engine.

• Fitting a manufacturer’s optional engine together with any associated components as supplied by the manufacturer for that same model vehicle.

• Fitting replacement original equipment (or equivalent) engine and exhaust components.

• Fitting replacement original equipment, equivalent or better, components that have no influence on engine performance or emissions. (e.g. higher volume oil pump than original)

In all of the above cases, if the engine is modified, it must be certified under the relevant Approval Code.

1.2 MODIFICATIONS REQUIRING CERTIFICATION UNDER LA APPROVAL CODES

• Fitting equivalent engines (within 20% of original power and engine mass).

• Fitting performance engines.

• Installing a supercharger or turbocharger.

• Modifying engines and engine components.

One reason is that generally to fit a FMIC you need to cut extra holes in your car for pipework.

If you cut holes without reinforcing hole perimeter you have reduced structural integrity of Monocoque chassis..(technically anyway).

Any modifications to car chassis obviously needs to be engineer certified...

There are other regulations that are State dependant...

i used john wilson of AKZ engineering. cost me $550 to engineer my coilovers, pod filter, non standard wheels, boost gauge, aftermarket pedals and turbo timer. it took about a week to get the report back from him andi had no issues getting my car registered. i know some people have had problems with him.. i believe one was naughtyruski

i used john wilson of AKZ engineering. cost me $550 to engineer my coilovers, pod filter, non standard wheels, boost gauge, aftermarket pedals and turbo timer. it took about a week to get the report back from him andi had no issues getting my car registered. i know some people have had problems with him.. i believe one was naughtyruski

I've dealt with John on my previous car modification pre-skyline.. Not going to say anything here.

I went to Ray Spence to get my engineering done (POD, Wheels, FMIC, Exhaust) for $550. Took 8 hours to get the report in my hands (dropped off in the morning, picked up in the arvo). I think it was Mick that actually put me on to Ray Spence (cheers for that).

On the note of needing an engineer's cert for mods, where I read that, it also stated that interstate certificates are sufficient. Would a Queensland "modplate" count for this? If all mods have been certified and the car has been given this "modplate", I'm wondering if that will count enough.

I've dealt with John on my previous car modification pre-skyline.. Not going to say anything here.

I went to Ray Spence to get my engineering done (POD, Wheels, FMIC, Exhaust) for $550. Took 8 hours to get the report in my hands (dropped off in the morning, picked up in the arvo). I think it was Mick that actually put me on to Ray Spence (cheers for that).

x2 about not saying anything, I could say a massive amount.

I highly recommend Ray Spence. :cool:

Called Dickson Motor Registry this arvo, the modplate doesn't count for anything unless it's backed up by signed paperwork...that isn't necessarily a problem at this point, at least all the mods are done properly so getting an engineer's certificate from Ray when I've got the car won't be a trouble...only more money >.<

Other than the engineer's certificate, can anyone see any real reason I shouldn't grab this car while I can? http://www.skylinesaustralia.com/forums/R3...ht-t242518.html

Currently asking $14000 (plus $521 to send it to Canberra), and it has a new clutch as stated on the last page.

Thanks :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...