Jump to content
SAU Community

Hks 2530 Turbo Induction Noise?

RubyRS4

By RubyRS4,
in Engines & Forced Induction

 Share

Recommended Posts

RubyRS4 Grand Master

RubyRS4

Posted
Posted

Can anyone tell me if it IS normal for a HKS 2530 turbo to make spooling noises (like a whistle)?

Is this normal induction noise.

:(

Also, does a bellmouth dump pipe provoke noise at high rpm from the wastegate opening? (like a muffled screamer?) ... or would this signify a leak between the turbo and dump pipe?

Link to comment
https://www.sau.com.au/forums/topic/264033-hks-2530-turbo-induction-noise/
Share on other sites
RubyRS4 Grand Master

RubyRS4

Posted
  • Author
Posted
I have the same turbo. With an atmo BOV no whistle. If I run a recirc, I can hear the compressor whine until the BOV closes.

Yeah, I've heard the faint 'whistle' is normal for HKS turbos ... just needed reassuring ... someone else says 'no'.

My BOV is recirc back into intake.

I'm guessing the higher pitched noise is either the wastegate opening to release ex gases into my bellmouth dump pipe ... or its a loose nut (or gasket) around the turbo-to-dump or turbo-to-manifold.

Fry_33 Proficient

Fry_33

Posted
Posted

I've got a 2530 on my R33 GTST and it whistles too. I too wasn't sure if this is right. It has been checked and no vacuum leaks could be found. Mine starts to whistle at about -0.8 Bar and then it becomes harder to hear after about 0.5 Bar or somewhere there. I'd be interested to hear some other peoples experiences. I've got the standard plumb back BOV, standard air filter and HKS dump.

What boost are you rinning?

Lithium Grand Master

Lithium

Posted
Posted
- intake piping... rubber or metal

- Pods... filter type, metal frame, plastic frame and so on

The causes of the most obvious "Turbo whistle" noise that HKS turbos are often recognized by is anti-surge compressor covers - HKS GT-RS, GT2835, GT3037, T51Rs and T62Rs all have it though I wasn't aware of anything smaller having that kind of housing though I guess they could have done it with the GT2530s etc just to be special :)

hypergear Grand Master

hypergear

Posted
Posted

depends on the noise it makes. The Shinnning noise is normal, If its making a Zzzz... zz... noise, very noticeable when you switch off the car then it means bearing cartridge needs to be checked.

  • 5 weeks later...
DuFFR32 Collaborator

DuFFR32

Posted
Posted

Iv'e noticed a whistle with my HKS 2530 to be more pronnounced after changing to plumb back, its like the turbo spools up to a certain speed at like -0.08bar then as it comes onto boost gets harder to hear and goes away as soon as its on 0.5bar + my 32 is tuned to run around 16psi but the whistle noise im more aware of now since the change from full atmo to plumb back.... does it have to do with the way the air circulates around the intake pipe?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...