Jump to content
SAU Community

Galston to Gosford Cruise 8:30pm 17/10/2003 (Formerly Midnight cruise - Friday 17th)

Moanie

By Moanie,
in Events Archive

 Share

Recommended Posts

  • Replies 161
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

CS_180 Mentor

CS_180

Posted
Posted

coolies

as for the cops if ure not doing anything wrong or being a dick they generally leave u alone.........

moanie let us know when u guys are getting close to kariong and the coastie boys and girls will meet up with you....

0427231710

Tosh Grand Master

Tosh

Posted
Posted

CS_180, if Lozza's going to be along, I'll send him an SMS when we pass the end of the Old Pac (the round about up from the col der sac (spelling??) )

Can you confirm if he'll be attending?

benm Grand Master

benm

Posted
Posted

...considering it takes me 30-40mins just to get to the meeting point :D

Being a Westie does have 1 or 2 bad points, they can't all be good.

Tosh Grand Master

Tosh

Posted
Posted

Mona not 33

I think we should use a different channel, say perhaps 20 but I guess we can discuss this @ Thornleigh

benm: you're bringing skanks mate you can't pull out

 Share
Go to topic listing


  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Nope, I don't like the look of ND RF, or any ND really, I don't like their faces or arses, why, because of their "modern" lines, the NC, whilst "modernish" has a more rounded shape that I like Well, that's how my overly judgemental eyes see it anyway  
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      I definitely know the first rule here, look first, ask second. I've seen many people get roasted 😂 I found a few diagrams for the RB, but I'm yet to come across one for the VQ. From what I have read, the pump gets the +12v along with the FPCM, and it's the negative wire that gets passed through the resistor to regulate the voltage. So I assume I can just ground the negative wire at the pump to eliminate the FPCM control. But I really wanted to see the VQ circuit diagram first to make sure I understood it correctly. Once the new pump is in I'll do some testing to see how it behaves, and in the meantime, I'll keep looking for a wiring diagram. Thanks for your help mate, your time is greatly appreciated.    
    • GTSBoy
      Jacks that fit under GTR lips that can reach the subframe?

      By GTSBoy · Posted

      Maybe? I have the Supercheap ToolPro low thingo. It has a somewhat smaller diameter lifting "bowl" than you would expect on a workshop grade trolley jack, and a split rubber pad to suit that diameter. It clears the "N1" style skirts I have. Probably wouldn't if the jack's bowl and a suitably larger rubber block were in use. Having said that though.....you only need the rubber block to exist on the inner side of the pinchweld, so could carve away any rubber that fouled the skirt, leaving some there for "insurance" </simples>
    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      I used to do that (sills with rubber jack block).. ... then I got side skirts, and there's no way for the jack to actually work there, the jack pad itself on the jack is too big. Is the answer to use a... smaller (?) jack? Hmmm.
×
×
  • Create New...