Jump to content
SAU Community

Recommended Posts

I'd go 1000's, straight up.

i would buddy but theres like a 500bux differnece in price, bitch of a cold start and exhaust idle. =[

Would 1000cc Sards be ok to Run a 26/30 on E85 pushing 400-500kw?

Sorry to hijack

theyd be fine, only reason im asking is maybe they might be to overkill.

Edited by VB-
i would buddy but theres like a 500bux differnece in price, bitch of a cold start and exhaust idle. =[

I went with 750's and now looking at having to move them on for something bigger - given hindshight I would have saved money if I'd gone 1000's first time around.

What ecu are you using to be concerned about injector control?

I went with 750's and now looking at having to move them on for something bigger - given hindshight I would have saved money if I'd gone 1000's first time around.

What ecu are you using to be concerned about injector control?

well ive always planned to use the PFC D jetro.......but some have raised the question about Haltech.....problem is i dont think they have a plug and play unit =[

I would go 1000cc, low impedance. Trying to make motor with 1000cc, high impedance, injectors idle would be an absolute prick.

The reaction time of a low impedance injector is a lot faster, hence the motor will idle more smoothly, than if you were to use a high impedance injector.

I would go 1000cc, low impedance. Trying to make motor with 1000cc, high impedance, injectors idle would be an absolute prick.

The reaction time of a low impedance injector is a lot faster, hence the motor will idle more smoothly, than if you were to use a high impedance injector.

im in the same boat, in the sard range there are 2 options:

1. black top/orange tip, lag time 1m/s

2. light blue top/green tip, lag time .85m/s

is the 1st injector low impedence you are referring to?

i run 1000cc sards and bigger cams than mentioned and idle is no problem at all. cold start idle was never the greatest but i aint running the idle air control valve any more and never really cared as it wasnt a daily driver. I had to keep the revs up a touch for 30 secs and then it idled itself fine, dont think this is the injectors fault though.

1000's in a 14mm fuel rail. 1600's if you want to run e85. i have 1000's and at 376kw they are on 75-80% cheaper to get 1 set not having to buy smaller ones only to run out of RELIABLE headroom..

1000's idle perfect, just depends on your tune,, oh and ecu

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...