Jump to content
SAU Community

Recommended Posts

Cool, I'll be on my way around to collect it in 5 minutes :)

That is a good price, I had a quick squiz on Ebay to see what they were going for. I would have gone down the NisTune road but it appears the M35 computer doesn't like the current versions of the NisTune boards available.

Let us all know how you go with the E-Management Ultimate, sounds like a cost effective solution instead of replacing the whole ecu system.

Let us know how it all goes, I did a bit of work on the ECU pinouts and have put together this drawing. There was some common inputs that I couldnt find / stopped trying to find on the harness like boost & O2 so if you know what pins these are then let me know.

ECU_Pinouts_Model__1_.pdf

well, pending avaliability next weekend - and thanks to your diagram - ill install it and get it running (with everything unadjusted) to make sure it works. then it will be a wait for the mods to happen before a drive to melbourne for a tune!

thanks for the offer of help, ill post in here so its available to anyone else that might be doing the same thing

well, pending avaliability next weekend - and thanks to your diagram - ill install it and get it running (with everything unadjusted) to make sure it works. then it will be a wait for the mods to happen before a drive to melbourne for a tune!

thanks for the offer of help, ill post in here so its available to anyone else that might be doing the same thing

No problems, Ive been waiting for a fully tunable ECU alternative, like FLASH'g the existing or aftermarket ECU but no one has done this yet. Im using SAFC2 at the moment and its working fine but not very tunable.

ok so im set to install this on the weekend.

the only thing that worries me is the settings on the actual unit, the jumpers, and also the firing order for ignition

in my S15 i had to wire 1,2,3,4 to 1,3,4,2 due to a 4 cylinder firing order, i destroyed 2 coilpacks with incorrect wiring, and i dont want to risk that on this car.

they mention V6 engines, and with nissan being nissan they will probably have kept it fairly standard config. im going to google emanage ultimate installs on a VQ35DE engine from the states, i believe they act the same, even if the ECU is wired differently.

fingers crossed!!!

ok here is an install doco for G35 (US) that looks pretty good. ignore the wiring to the ECU, however his technique and setup is good, and it covers some nissan 'problems' etc.....

DandyMaxEUWriteup.pdf

may as well keep all the Emanage Ultimate stuff in the same place. make it easier for other guys to find and us to assist with

so once ive done my install, are you gonna drive to sydney to get me to do yours too?? :)

cheap rates :):P

may as well keep all the Emanage Ultimate stuff in the same place. make it easier for other guys to find and us to assist with

so once ive done my install, are you gonna drive to sydney to get me to do yours too?? :)

cheap rates :):P

Haha. You would have to be bloody cheap.

Remember I can get it installed & tuned for a damn good price.

Edited by iamhe77
are you gonna drive to sydney to get me to do yours too?? :)

cheap rates :P:P

Ahem... I do hope you are referring to the E-Manage Ultimate :)

I'll be interested to see how it goes and what you think of it after it's had an optimal tune :D

I assume you are going for high output rather than fuel efficiency ;)

But I'm sure you can adjust that on the fly or atleast with a laptop running windows?

I've got a apple laptop so that wouldn't be too good for the whole USB software adjustment etc.

ahh yeah damn i forgot you were already IN melbourne for that tuner lol

yeah you can tune it on the fly with a laptop, but id be doing it on a dyno so its done properly.

ill be tuning for less fuel down lown, and more power up top because i drive easy around the city where i need economy, but when i put my foot down i dont give a shit lol

id be doing it on a dyno so its done properly.

ill be tuning for less fuel down lown, and more power up top because i drive easy around the city where i need economy, but when i put my foot down i dont give a shit lol

+1 (or is that +2?)

so yesterdays install didnt occur. the pin layout diagram i have may be incorrect. i was metering out +12v and 0v and neither of them were correct. so either i cant use a multimeter anymore, im reading it backwards, or the diagram is incorrect.

not sure what im going to do at this stage.............. might try again when i dont have a headache lol

so yesterdays install didnt occur. the pin layout diagram i have may be incorrect. i was metering out +12v and 0v and neither of them were correct. so either i cant use a multimeter anymore, im reading it backwards, or the diagram is incorrect.

not sure what im going to do at this stage.............. might try again when i dont have a headache lol

Hmm... Too many variables there.

Perhaps ask URAS (Trent from Status Tuning - here in Melb)

Also, check out his eManage Ultimate thread.

Edited by iamhe77

nah no updates mate, with mothers day yesterday i didnt get a chance. ill see whats on this weekend before i give it another go. im prepping the wiring so the hopefully ill just need to plug it in after i crimp the wires

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...