Jump to content
SAU Community

Recommended Posts

  • Replies 192
  • Created
  • Last Reply

Top Posters In This Topic

might even drive alright once its had an alignment

the day after it was registered it was at the track

ive already told jenna to start saving 10k for the new engine

lol

and ive discovered that it cant rip a 3rd geaar bunout at its current power level

:rolleyes:

fark 137kegs you will look positively anorexic.

no need for $10K engine. I have a nice, complete RB26 out of a 1994 R32, wide crank drive, excellent compression, all yours for $3750. guaranteed to chirp something...

beer baron need money. hence RB26 out the door! :P it's fully running and with good compression (had it checked before it was pulled out of the car). has a brand new sump on it too as it was replaced with a new R34 N1 Nur motor and for ease of install we took the sump off the 32 motor and slapped it onto the 34 motor. it wasn't out of a wreck or anything. Just clean 1994 R32 GTR we bought and put a new N1 Nur motor in. anyway, if anyone wants it I'll be putting up a FS thread soon.

that's a big 10-4. 32 diff gears are plentiful though if needed for anyone.

in a slightly related matter I just got a line on sets of brand NEW 4.375:1, R32 GTS4 diff gear sets for front and rear (both crown wheel and pinions). they are not much more than the $$$ people charge for second hand ones to poor GTR owners like me.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...