Jump to content
SAU Community

Recommended Posts

  • 3 months later...

I'm biased, but I like XD9's

My car:

5887567232_dd75cae8d3_b.jpg

5886982719_426fbab819_b.jpg

5887032521_bf4d91009f_b.jpg

Hey looks good, what size/offset do you have on your car?

and what sort of gaurd work was done?

Edited by MatthewT85
  • 2 weeks later...

Where were people getting the buddyclub p1 rims in 18" from, preferably matte black?

I can seem to find any retailers online that sell them.

There is the rota boost rims which are the same design and cheaper but I would like legit p1s if I can get them.

staggered set of enkei rfp1's

check out this car. looks pure dope, colour, offset and everything. im seriously considering enkeis after these shots.

http://www.stancenation.com/2011/02/21/teenage-dream/

YES! its stance nation, not all threads on there are tooooooo bad. its not like its an EG civic with 18x10s etc, i dont need to seeee anymore of those things. yock!

staggered set of enkei rfp1's

check out this car. looks pure dope, colour, offset and everything. im seriously considering enkeis after these shots.

http://www.stancenation.com/2011/02/21/teenage-dream/

YES! its stance nation, not all threads on there are tooooooo bad. its not like its an EG civic with 18x10s etc, i dont need to seeee anymore of those things. yock!

Blags's car

ok i know this is the wrong section but getting no luck anywhere else -

My question is , will these rims fit on my stock r33 skyline series 2. I know I probably need to get the fenders rolled but other then that , will I have issues with fitment for the rear?

They are Volk SF Challenge Zero's , old school volk wheel , came out in 97'

Front :

18x9.0 +45 235 tyres

235offset.jpg

Rear:

18x10.0 +48 275 tyres

offset275.jpg

cheers

GTR wheels are 9" +30 all round from memory and they fit on gtst's without any work im pretty sure

So, 9" at the front should be ok with a 235 tyre, thats a real high off set though.

Not real sure on the 10" on the rear, I have only really seen 9.5" on the back.

IMO With those offsets, they arent going to look great if they do fit, unless you run spacers.

Edited by Mitcho_7

To get an idea of what they'll be like, the car at the top of this page with the XD9's has (I assume) 18x10" +18 on the rear. So your wheels will sit 30mm further in than those. I had the same and they poked out about 5mm so +48 will be fairly sunken.

Put them on and see what you think anyway. I have a feeling though you may not have enough inner clearance with those offsets.

GTR wheels are 9" +30 all round from memory and they fit on gtst's without any work im pretty sure

So, 9" at the front should be ok with a 235 tyre, thats a real high off set though.

Not real sure on the 10" on the rear, I have only really seen 9.5" on the back.

IMO With those offsets, they arent going to look great if they do fit, unless you run spacers.

To get an idea of what they'll be like, the car at the top of this page with the XD9's has (I assume) 18x10" +18 on the rear. So your wheels will sit 30mm further in than those. I had the same and they poked out about 5mm so +48 will be fairly sunken.

Put them on and see what you think anyway. I have a feeling though you may not have enough inner clearance with those offsets.

thanks for the advice , il fit it tomorrow and see how they sit.will post pics when they are on

oh and sorry for the thread jack

cheers

To get an idea of what they'll be like, the car at the top of this page with the XD9's has (I assume) 18x10" +18 on the rear. So your wheels will sit 30mm further in than those. I had the same and they poked out about 5mm so +48 will be fairly sunken.

Put them on and see what you think anyway. I have a feeling though you may not have enough inner clearance with those offsets.

so they didnt fit , as suggested no inner clearance at all , what kind of spaces would I need?where would i buy it from?

oh and my vote goes for the professors! beautiful looking wheel

so they didnt fit , as suggested no inner clearance at all , what kind of spaces would I need?where would i buy it from?

oh and my vote goes for the professors! beautiful looking wheel

I'd say if you wanna go spacers you'll need 25mm bolt ons front and back. Never used spacers before so not sure where you'd get them, Justjap maybe? Best let someone else reply who'd know better for wheel studs etc.

With 25mm you'd technically be on +23 offset rear and +20 front. Will be fairly flush then if you consider my post just above yours in reply to the quoted pic. You'd be 2mm more outwards on the front and 5mm inwards on the rear compared to that black R33.

I'd say if you wanna go spacers you'll need 25mm bolt ons front and back. Never used spacers before so not sure where you'd get them, Justjap maybe? Best let someone else reply who'd know better for wheel studs etc.

With 25mm you'd technically be on +23 offset rear and +20 front. Will be fairly flush then if you consider my post just above yours in reply to the quoted pic. You'd be 2mm more outwards on the front and 5mm inwards on the rear compared to that black R33.

thanks for the advice, found some :

http://www.ebay.com.au/itm/NEOTECH-NISSAN-5-Stud-114-3-25mm-Bolt-Wheel-Spacers-/130708637330?pt=AU_Car_Parts_Accessories&hash=item1e6ed78692

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...