Jump to content
SAU Community

Recommended Posts

Am i need to borrow or even buy a set of 17' rims with 225/45 profile as my defect is making me go with my tyre placard.. my car never came with the r34 stockies so am in need of some. if you have any lying around please let me know!

Link to comment
https://www.sau.com.au/forums/topic/268805-r34-17-stockiesrims/
Share on other sites

rims too big pat...?.... i had 19's on. he made me comply to tyre packard 100% with the same tyres as it says 225/45 on packard. = r34 stockies..

im tired of these stupid laws. and getting lectures saying that lowering my car stuffs up the aerodynamics and handling bla bla. and bigger tyres are bad.. some cops really dont know what there talking about do they..

all sorted. :P thanks Ian & Ashneel for the rims and bonnet :)

got my engineer cert so shouldnt have that problem again!!

Lol at the time posted haha, you got to tell me that engineer!!! :D i need one for my hood too...soo gay

Hey bez, im sure my bro will be fine with it, got his R34 stockies with 225/45 rubber on em. If you need em give me or him a call :D

Hey btw what tire size is ians new 18" going on? :S didnt check when he came by here...

Who was telling you that you need the exact same size as the placard engineer/cop/rwc guy, i got through my defect with 18's and 235 tyres on a car that came with 16's.

the engineer did mate. the defect was listed

bonnet - engineers report required, etc apply with ADR's

rims/tyres - to comply with tyre packard.

trust me i tried everthing to clear it without changing my 19's with 235 front 265 rear. but yeh didnt work.. see i tried to put on a stock bonnet and clear it but vicroads basically kept telling me to go away just cause it says engineers report required.. even if i put a stock bonnet back on.. sigh. was a headache. and the engineer told me if hes engineering just for a stock bonnet he might aswell just write one for the whole car since my ride height was a low aswell (have adjustable coilovers) i changed them to a standard height, put ians stockies on and still have stock bonnet on and got whole thing engineered.. 700 bucks later zz..

what was annoying was when i first got the defect and the cop gave me a lecture on why i shouldnt change a cars factory build because its stuffs it all up to what its meant to be built to. even got told putting bigger tyres on is unacceptable because it doesnt comply with my tyre packard.... 225/45 17's.

anyway all done and cleared. time to move on and keep car standard for a bit .... lol

the engineer did mate. the defect was listed

bonnet - engineers report required, etc apply with ADR's

rims/tyres - to comply with tyre packard.

trust me i tried everthing to clear it without changing my 19's with 235 front 265 rear. but yeh didnt work.. see i tried to put on a stock bonnet and clear it but vicroads basically kept telling me to go away just cause it says engineers report required.. even if i put a stock bonnet back on.. sigh. was a headache. and the engineer told me if hes engineering just for a stock bonnet he might aswell just write one for the whole car since my ride height was a low aswell (have adjustable coilovers) i changed them to a standard height, put ians stockies on and still have stock bonnet on and got whole thing engineered.. 700 bucks later zz..

what was annoying was when i first got the defect and the cop gave me a lecture on why i shouldnt change a cars factory build because its stuffs it all up to what its meant to be built to. even got told putting bigger tyres on is unacceptable because it doesnt comply with my tyre packard.... 225/45 17's.

anyway all done and cleared. time to move on and keep car standard for a bit .... lol

What sort of bonnet did you have and did you try to get it engineered or just go the easy route with the standard bonnet?

had a fibre glass vented bonnet, well the bonnet got engineered but for some reason they wouldnt except the report until stock bonnet was on so =S did put on standard bonnet but still required to get cert for other bonnet which was really stupid and a big waste of time... and money

had a fibre glass vented bonnet, well the bonnet got engineered but for some reason they wouldnt except the report until stock bonnet was on so =S did put on standard bonnet but still required to get cert for other bonnet which was really stupid and a big waste of time... and money

Let me know the engineer now!!! :( i wanan get mine done..but by the soudns of it theres no point regardless...but might aswell ask...let me know :blink:

  • 2 weeks later...
rims too big pat...?.... i had 19's on. he made me comply to tyre packard 100% with the same tyres as it says 225/45 on packard. = r34 stockies..

im tired of these stupid laws. and getting lectures saying that lowering my car stuffs up the aerodynamics and handling bla bla. and bigger tyres are bad.. some cops really dont know what there talking about do they..

http://www.vicroads.vic.gov.au/NR/rdonlyre...8340/0/VSI8.pdf

"The overall diameter of any replacement rim and tyre must not be;

- More than 15mm greater than largest diameter tyre specified by the vehicle manufacturer for that model or vehicle series"

* Convert the metric measure to inches by dividing by 25.4. (225 ÷ 25.4 = 8.86 inches)

* Multiply the section height in inches by the aspect ratio (in this case, 45) to determine the section height. (8.86 x 45% = 3.987 inches)

* Multiply the section height by 2, then add the wheel diameter as noted in the tire size. In this example, the wheel diameter is 16 inches. (3.987 x 2 + 17 = 24.974 inches – Overall Tire Diameter)

* 24.974 inches to cm is 63.43 centimeters

Lets say you have 245/35/R19

* 245 ÷ 25.4 = 9.65 inches

* 9.65 * 35% = 3.376 inches

* 3.376 x 2 + 19 = 25.752 inches - overall tyre diameter

* 25.752 inches to cm is 65.41008 centimeters

Soooooooooo the difference is 1.98cm, which is 20mm hence illegal haha

But if you have 235/35/R19

it equals; 64.71cm

Which is 1.28cm difference; 12.8mm difference and hence it is legal?

No idea if im right or not, explain that to a cop and you'll be right.. :ninja:

What tyre size you got on the 19inch?

http://www.vicroads.vic.gov.au/NR/rdonlyre...8340/0/VSI8.pdf

"The overall diameter of any replacement rim and tyre must not be;

- More than 15mm greater than largest diameter tyre specified by the vehicle manufacturer for that model or vehicle series"

* Convert the metric measure to inches by dividing by 25.4. (225 ÷ 25.4 = 8.86 inches)

* Multiply the section height in inches by the aspect ratio (in this case, 45) to determine the section height. (8.86 x 45% = 3.987 inches)

* Multiply the section height by 2, then add the wheel diameter as noted in the tire size. In this example, the wheel diameter is 16 inches. (3.987 x 2 + 17 = 24.974 inches – Overall Tire Diameter)

* 24.974 inches to cm is 63.43 centimeters

Lets say you have 245/35/R19

* 245 ÷ 25.4 = 9.65 inches

* 9.65 * 35% = 3.376 inches

* 3.376 x 2 + 19 = 25.752 inches - overall tyre diameter

* 25.752 inches to cm is 65.41008 centimeters

Soooooooooo the difference is 1.98cm, which is 20mm hence illegal haha

But if you have 235/35/R19

it equals; 64.71cm

Which is 1.28cm difference; 12.8mm difference and hence it is legal?

No idea if im right or not, explain that to a cop and you'll be right.. :D

What tyre size you got on the 19inch?

rekin the engineer to the rescue :)

such a geek lol!

haven't seen ur car around monash for a while u still go there?

rekin the engineer to the rescue :D

such a geek lol!

haven't seen ur car around monash for a while u still go there?

haha still do, 4th year is killing me.

I always park at the back of the ground level. Between a pillar and the road so no one can park next to me :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The ATTESSA is functionally identical to R34; there were a bunch of JDM models that continued ATTESSA including Fuga/Q70, Skyline/Q50, Cima etc as an option. All with Auto only and I think mostly for snow regions. AFAIK there were no AWD VR30DDTT sold in Australia - it is on my to do list to check regs for racing a LHD car in Targa/ATR/AASA/CAMS events because if I can get the auto to work it would be interesting to run a 4wd car The Ecuteck TCM tuning is the same model as their ECU tuning, they already have it for R35 and Dose's favourite, BMW. You buy "points" to allow your computer to be tuned, buy either a bluetooth (phone app) or bluetooth+USB+Key (phone and PC) dongle, and pay for a tune that will be locked to your tuner ( ). You can also access the tuning software yourself but 1. it is mega expensive and 2. these computers have a billion parameters that intersect, so how could you ever spend enough time on it to get a decent result.
    • Or, is it a case of what it is like owning an R series Skyline? NFI what the previous owner has done or fiddled with... Ha ha ha After reading through this thread, I went on a bit of a research about the Q50/Q60. Now I'm quite intrigued by them! Is the AWD in them more like a WRX where it's always AWD, or is it more like the ATTESSA in the GTRs? By the sound of this TCU tuning, this sounds like a case of someone has made some real software for it, and you just need the right piece of hardware, and then you license that specific vehicle/TCU. Or is this a case of the software will be really expensive so only a few tuners have it, and you still have to pay a license per vehicle?
    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
×
×
  • Create New...