Jump to content
SAU Community

Recommended Posts

G'day I'm from Adelaide and I've got a series 1 stagea which I recently purchased.

Unfortunately I didn't notice when checking it out the idle is somewhat erratic (revs high (1500 or so, then drops to 500 or so, then usually settles). It's only really noticeable just after starting it up and during some low speed turns. Not really a big problem but definitely something I would like to fix.

Also occasionally the engine has cut out a few times during sharp low speed turns, which I'm guessing has some relation to the idle as maybe increased load on the engine and no extra revs could cause it. This is obviously quite frustrating.

Anyone else encountered these problems and could offer suggestions for fixing?

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/269756-problems-with-series-1-stagea/
Share on other sites

It could be a lot of things but cleaning out your AAC valve would be a prime suspect. There is a great tutorial here:

http://www.skylinesaustralia.com/forums/Di...nd-t110431.html

the links to the photos do not work but the photos have been put back in if you scroll down a bit.

Well worth doing and could solve your problem.

blocked of blow off's tend to affect the cars low down rpm and can cause stalling ect..

I'd be doing the following:

Clean ACC valves

Checking plug gap and condish.

Make sure blow off isnt plated off

any idea when fuel filter was last done?

Cheers for the tips, I'll have a go at a few things and post up any results. Don't hold your breath though!

No idea when the fuel filter was last done

Also the last service included works for fixing a leak in the vac rear of the inlet manifold. Could this be a possible cause of the problem? eg maybe its leaking again?

I really hope I can get this sorted, as I really like the stagea. Currently pretty disappointed :whistling:

Which part of Adelaide are you located?

There are a few potential causes - all pretty simple (some mentioned already), so it might pay to hook up with another owner who can offer advice.

I have access to factory diagnostic tools if you suspect a dud sensor.

It will also pay to check the type of plugs installed - some compliance parts are 'average' to say the least...

When Igot mine three years ago it did all that. But it went away. There was some suggestion about stale fuel being in the tank. The other suggestion was to reset the ecu by disconnecting the battery negative and pump the brake a few times, then reconnect.

Cheers for the further help.

On the whole it still drives pretty well, certainly is a pleasure. I just really want to get it as close to perfect as possible.

Oh and I'm from the noth western suburbs and I'd be keen to see if there's any sensors showing problems. You anywhere near me bensdr30?

Edited by stoks1
I make regular surfing trips down south, so that shouldn't be a problem.

I'd PM ya but I don't have enough posts yet haha (need 10 minimum before you can)

Do a couple more posts and let me know via PM when you're heading past Old Noarlunga next - we'll plug the laptop in & see if there's anything obvious going on.

(and eyeball the engine bay - you never know what might show up)

  • 4 weeks later...

Just thought I'd resurrect this and say I got round to getting a new O2 sensor fitted with limited results. It definitely runs better but still feels very sluggish as if it will stall during low speed maneuvers, so it was worth doing but it didn't fix it.

I guess I'll try AAC valve and plugs next.

Well that's a start...

One thing we didn't test when we had NDS hooked up was the AAC function. :bunny:

I was playing around on our car on the weekend & remembered that you can set the AAC and check for the appropriate RPM change (I think it ran at about 600rpm with the AAC set to zero, and about 1600rpm with it set to 100).

If you're heading on another surfing trip, feel free to drop in & we can give it a test.

:rofl:

  • 2 weeks later...

Hey guys im having pretty much the same issue as Stoks with almost identical car and the idling was getting pretty bad fluctuating from about 1000rpm to stalling while sitting in drive in traffic (even worse while in park) so i went and got the car serviced and they cleaned the AAC valve, did a throttle body service and reset the idling. was fine for about 2 days but now its getting worse change gears when the car is warm and it flutters between 1000rpm and almost cuts out. easiest way to deal with it i've found is to drive with the A/C on to lift the revs but that obviously isnt a good idea for fuel so... i need help! Spoke to the mechanic that worked on my car and he said the engine was A1 but thinks i might have a faulty AAC so i was wondering if anyone knew if if was common for the AAC to fail (understandable with a 12yr old car) and if so can you find replacements?

any help would be appreciated

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lets say I wanted to buy this, specifically for this purpose. How do I actually perform the function. Can I still buy a Consult-1? Am I about to be burned by the fact my car is a 2000 model Series 2 R34 and thus will be some stupid other system? Do I just need this -> https://obd2australia.com.au/product/nissan-consult-14-pin-to-usb-ddl-diagnostic-interface-with-ftdi-ft232r-chip/ And with what software?
    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
×
×
  • Create New...