Jump to content
SAU Community

Recommended Posts

I have a problem with my car again its a R33 S2 and it is missfiring, I know this topic has been covered tons of times but I have fixed the missfire previously by buying new coilpacks. I bought JJR coilpacks and the missfire was gone for maybe 6 months, the car reved very smoothly all the way to redline... and now I'm getting a missfire at about 5000-5500rpm and up until then the car feels flat like it has no balls and then at about 6000rpm it feels like it takes off until redline.

Could this be that the coilpacks have fudged them selves?

Also I have replaced the spark plugs with iridium ones about 6 months ago just before i changed the coilpacks.

Any ideas? Could it be a injector?

Link to comment
https://www.sau.com.au/forums/topic/271189-missfiring-again/
Share on other sites

there is a sticky in general maintenance, they say to tape up your coils due to tiny cracks in them(electrical tape). Might be worth checking a very cheap option, at least the u can diagnose the problem this way.

+1

Worked for me

there is a sticky in general maintenance, they say to tape up your coils due to tiny cracks in them(electrical tape). Might be worth checking a very cheap option, at least the u can diagnose the problem this way.

I got new JJR coils, they shouldnt need to be taped...but i guess if it stops missfirring when they are taped then this just means they are arking out then they are fooked...

My plugs are gapped to the standard irridium plug size which is 12mm i think. But they shouldnt need to be gapped if i got new coil packs rite??? They should be strong enough to make the spark jump accross stock gapped spark plugs?

Edited by da spike

change the plugs to BCPR6ES gapped to .8mm then put a little mark in texta on the spark plug where the electrode is open (ie where you can see the most of it) when doing up your spark plugs point that mark to the inlet manifold you would be surprised how often this will fix your problems you want the mixture to be ignited if the electrode is facing the exhaust manifold it wont run as well small point but makes a big difference

I'm interested in seeing what happens. I have spitfire coils and gapped my plugs to 0.8mm as almost everyone recommends and it run absolutely crap after 4,000 rpm, gapped them to 1.1 and revs out to redline beautifully.

i installed my splitfires today along with new plugs gapped to 0.8mm, idle's fine but when i go to drive my car is missfires hardcore even at low revs...! rkn i should regap to atleased 1mm?

Another question... how do you guys gap the plugs without fooking them? Just tap them down with a small hammer?

I just gave it kinda firm knocks on my workbench and a feeler gauge to verify the gap - seemed to do the trick fine.

I'm just thinking could this be RnR? Because i would find it hard to believe that the coilpacks would have shit them selves after a few months use and i have changed the sparkies too when changing coilpacks to irridium ones... The missfire or popping under acceleration usually happens on a really cold night, the car also feels like it has a flat spot from 4500rpm to 6000rpm and then from 6 onwards its fine...

if it is happening more when it is cold then it may be rnr. but remember that the VCT turns off at 4500rpm so you do get a bit of a flat spot there.

to gap the plugs you need a feeler gauge. basically it is a set of small sheets of metal all different sizes.

i personally think iridium spark plugs are a waste of time. the set in my old 33 were shagged after about 20,000kms. i put the ones listed above in and changed them after 10,000kms and they were still fine. they are only a few dollars a plug.

as for there the tip of the plug is and marking it with a pen and trying to align it with the manifold, you may find that doesn't always work, without ending up with either it too loose or way too tight. however it shouldn't really make a difference as the valve will be closed well before the spark plug fires

Ok I got BCPR6ES plugs and threw them in and took the car for a spin just quickly and it looks like its not missfiring anymore... :D But I will need to drive it more to make sure because sometimes the missfire would be tempremental..

But what it's still doing is running shit from about 4500rpm all the way to 6000rpm and then it kicks in hard. Do you guys think this is rnr?

By the way I'm running standard boost and its going up to about 9-10psi cause its a cold night and exhaust, intercooler.

i personally think iridium spark plugs are a waste of time. the set in my old 33 were shagged after about 20,000kms. i put the ones listed above in and changed them after 10,000kms and they were still fine. they are only a few dollars a plug.

The iridium ones i took out (i put these in about 10,000 kms ago) were pretty fouled up so i guess copper ones are the cheaper alternative...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...